Abstract:Fused deposition modeling (FDM) is a layered manufacturing (LM) process in which progressive 2D layers of material are kept making a 3D part. To optimize the building operation, the investigation is necessary to study the effect of process parameters. This study examines the impact of three filling patterns, "triangles," "cross," and "cross 3D," with three filling densities (25%, 50%, and 75%) in three orientations ("flat," "on long edge," and "on short edge") on ultimate tensile strength (UTS), hardness and the printing time of polylactic acid (PLA) material. This work built tensile specimens according to ASTM D638 on an open‐source 3D printer. The UTS was collected using a WDW‐2000 computer control electronic universal testing machine. The hardiness value was also measured using Shore A hardness durometers DIN 53505 and ASTM D2240. In addition, the building time was conducted by implementing the "Cura 4.6" slicer software. The results show that the filling pattern, orientation, and density at which the part is built significantly affect the strength, hardness, and building time. For light structure parts with 25% density, it is recommended to build parts with "triangles" "on long edge" to obtain the highest strength (31.02 MPa), which improved by 74.3%, with 281 HV at the minimum time (1 h:10 min), which was reduced by 46.1%. For dense structure parts, "triangles" and "on long edge" are recommended to give the highest strength (42.12 MPa), which can be improved by 69.8% (282 HV) at the minimum time (1 h:35 min), which was reduced by 36.2%. For medium construction, 50% of the parts can be built by the following parameters: "cross" and "on long edge" to obtain the highest strength (38.48 MPa) with 283 HV at the minimum possible time (1 h:55 min). The study could help with the growth of producing mechanically functional parts, such as prosthetics, using LM. In addition, the part can be built with high strength, hardness, and minimum building time, which is useful information for the best utilization of the 3DP machine. Also, the chosen parameters optimize the building process with little human intervention.

Strength improvement and failure analysis of dissimilar FDM printed single-lap joints with tailored interface geometry

Strength and failure assessments of 3D printed PLA single lap joints: Experimental and numerical analysis

Single-layer Temperature-Adjusting Transition Method to Improve the Bond Strength of 3D-Printed PCL/PLA Parts

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Enhancing shear strength in 3D printed single lap composite joints: A multi‐faceted exploration of GNP integration, print orientation, utilizing artificial neural networks, and dynamic analysis

Experimental and numerical study on mechanical behavior of 3D printed adhesive joints with polycarbonate substrates

Enhancing interlaminar adhesion in multi-material 3D printing: A study of conductive PLA and TPU interfaces through fused filament fabrication

On the Effects of Process Parameters and Optimization of Interlaminate Bond Strength in 3D Printed ABS/CF-PLA Composite

Optimization of adherend thickness and overlap length on failure load of bonded 3D printed PETG parts using response surface method

An experimental analysis of mechanical properties for a dissimilar pattern structure in the 3-D printing of a PLA5F filament using the Taguchi method

Adhesive bonding of similar/dissimilar three-dimensional printed parts (ABS/PLA) considering joint design, surface treatments, and adhesive types

Additive manufacturing of metal-polymer hybrid parts: the influence of as-printed LPBF surface roughness on the joint strength

On strain rate and temperature dependent mechanical properties and constitutive models for additively manufactured polylactic acid (PLA) materials

Improving Mechanical Performance of Fused Deposition Modeling Lattice Structures by a Snap-Fitting Method

Loading-rate effect on tensile and bending strength of 3D-printed polylactic acid adhesively bonded joints

Influence of 3D printed adherend design on structural performance and vibrational behaviour of adhesively bonded joints

Effect of printing characteristics for the incorporation of hexagonal-shaped lattice structure on the PLA polymeric material

Influence of Build Orientation and Part Thickness on Tensile Properties of Polyamide 12 Parts Manufactured by Selective Laser Sintering

Polymer-Metal Adhesion of Single-Lap Joints Using Fused Filament Fabrication Process: Aluminium with Carbon Fiber Reinforced Polyamide

The Impact of Various Filling Patterns and Building Orientations on the Mechanical Characteristics and Building Time of PLA Using FDM

The effect of processing parameters on the mechanical characteristics of PLA produced by a 3D FFF printer