Abstract:Fused Deposition Modeling (FDM) is a well-established manufacturing method for producing both prototype and functional components. This study investigates the mechanical properties of FDM components by material and process-related influencing variables. Tensile tests were conducted on seven different materials in their raw filament form, two of which were fiber-reinforced, to analyze their material-related influence. To cover a wide range from standard to advanced materials relevant for load-carrying components as well as their respective variations, polylactic acid (PLA), 30% wood-fiber-reinforced PLA, acrylonitrile butadiene styrene (ABS), polycarbonate (PC), a blend of ABS and PC, Nylon, and 30% glass-fiber-reinforced Nylon were selected. The process-related influencing variables were studied using the following process parameters: layer thickness, nozzle diameter, build orientation, nozzle temperature, infill density and pattern, and raster angle. The first test series revealed that the addition of wood fibers significantly worsened the mechanical behavior of PLA due to the lack of fiber bonding to the matrix and significant pore formation. The polymer blend of ABS and PC only showed improvements in stiffness. Significant strength and stiffness improvements were found by embedding glass fibers in Nylon, despite partially poor fiber–matrix bonding. The materials with the best properties were selected for the process parameter analysis. When examining the impact of layer thickness on part strength, a clear correlation was evident. Smaller layer thicknesses resulted in higher strength, while stiffness did not appear to be affected. Conversely, larger nozzle diameters and lower nozzle temperatures only positively impacted stiffness, with little effect on strength. The part orientation did alter the fracture behavior of the test specimens. Although an on-edge orientation resulted in higher stiffness, it failed at lower stresses. Higher infill densities and infill patterns aligned with the load direction led to the best mechanical results. The raster angle had a significant impact on the behavior of the printed bodies. An alternating raster angle resulted in lower strengths and stiffness compared to a unidirectional raster angle. However, it also caused significant stretching due to the rotation of the beads.

Synthesis and Investigation of Mechanical Properties of the Acrylonitrile Butadiene Styrene Fiber Composites Using Fused Deposition Modeling

On the Effects of Process Parameters and Optimization of Interlaminate Bond Strength in 3D Printed ABS/CF-PLA Composite

Effect of printing parameters on the mechanical properties of 3D printed short glass fiber/acrylonitrile butadiene styrene composites

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Experimental Study of the Tensile Behavior of Structures Obtained by FDM 3D Printing Process

3D Printing Parameter Optimization Using Taguchi Approach to Examine Acrylonitrile Styrene Acrylate (ASA) Mechanical Properties

Investigating physical and mechanical properties of alumina/acrylonitrile butadiene styrene composites manufactured by fused deposition modeling

Investigation of Effect of Part-Build Directions and Build Orientations on Tension–Tension Mode Fatigue Behavior of Acrylonitrile Butadiene Styrene Material Printed Using Fused Filament Fabrication Technology

Structure and Mechanical Behavior of Additive Manufactured Fused Deposition Modeling ABS

Mechanical properties evaluation of FFF-printed ABS samples based on different process parameters combined with ANOVA and regression analysis

3D Printing of Acrylonitrile Butadiene Styrene by Fused Deposition Modeling: Artificial Neural Network and Response Surface Method Analyses

Preparation and Evaluation of the Tensile Characteristics of Carbon Fiber Rod Reinforced 3D Printed Thermoplastic Composites

Effects of FDM-3D printing parameters on mechanical properties and microstructure of CF/PEEK and GF/PEEK

Correlation between production parameters and mechanical properties of ABS plus p430 fused deposition material

Effect of Infill Density and Printing Patterns on Compressive Strength of ABS, PLA, PLA-CF Materials for FDM 3D Printing

Study of Processing Parameters in Fused Deposition Modeling Based on Mechanical Properties of Acrylonitrile‐butadiene‐styrene Filament

An Investigation of Tensile, Fatigue, and Fracture Behavior of 3D-Printed Polymers

Failure Analysis and Mechanical Characterization of 3D Printed ABS With Respect to Layer Thickness and Orientation

Assessment of the mechanical properties of PC/ABS blends for functional prototyping by FFF 3D printing

Mechanical Properties of Raw Filaments and Printed Specimens: Effects of Fiber Reinforcements and Process Parameters

Analysis of mesostructural characteristics and their influence on tensile strength of ABS specimens manufactured through fused deposition modeling