Abstract:Selective laser melting (SLM) of the 7xxx series Al alloy (Al-Zn-Mg-Cu) faces more challenge than other series aluminum alloy such as Al-Si system because of the high hot-cracking sensitivity. The porosity development and crack behavior of Al-Zn-Mg-Cu alloys fabricated at various scanning speeds in SLM process, as well as the influence of molten pool geometry were systematically investigated in this paper. Results show that the relative density over 99% can be achieved when the applied scanning speed is 150 mm/s. However, cracks are observed in almost all the as-deposited samples. The morphology, distribution and density of cracks were varied with the different molten pool geometry and scanning speed. Introduction 7xxx series Al alloys are characterized by high tensile strength (over 500Mpa), high corrosion resistance and good fatigue properties [1-2]. These characteristics make over 85% of the 7xxx series Al alloys to use in automotive and aerospace fields. With the development of automotive and aerospace fields, the need for integral component of 7xxx series Al alloys is increased. The convention processing techniques encounter many difficulties due to the complexity and thin-wall structure of integral component. Hence, new manufacturing process like SLM is inevitable to enhance the process. SLM is an addictive manufacturing process with a high potential for producing complexly shaped components [3-4]. Because of the high thermal conductivity, poor fluidity and easy oxidized of aluminum alloy, up to now, only casting AlSi10Mg [5-8] and Al-12Si [9-11] have been widely manufacturing by SLM due to the weld ability and flow behavior. Few works have been focus on other aluminum alloys [12] especially the 7xxx series Al alloy. So far, Kaufmauu et al. [13] fabricated EN AW 7050 alloy sample with a relative density over 99%. However, all samples exhibited cracks. Sistiaga et al. [14] obtained crack free Al7075 alloy samples by adding 4% silicon in SLM process. Wang et al. [15] reported that an Al-Zn-Mg-Cu alloy with high zinc was successfully produced by SLM. The hardness of the synthesized SLM samples was higher than the corresponding T6 cast samples after heat treatment. The present work investigated the feasibility for fabricated full dense Al7050 alloy. The morphology, distribution and density of cracks were also discussed under different scanning speed and molten pool geometry.

Hot Impression Creep Behavior of AlSi10Mg Alloy Fabricated through SLM Route

Effect of Cross-Rolling on the Hardness of the AlSi10Mg Alloy Fabricated through Powder Bed Fusion

Microstructural analysis and mechanical properties of AlSi10Mg alloy components produced via SLM

Comparative analysis on high temperature tribological behaviour of additive manufactured and cast AlSi10Mg alloy

The AlSi10Mg Samples Produced by Selective Laser Melting: Single Track, Densification, Microstructure and Mechanical Behavior

An Experimental Investigation into the Dry Reciprocating Wear Behavior of Additively Manufactured AlSi10Mg Alloys

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Microstructure, wear and residual stresses of selective laser melting AlSi10Mg solid cylinder

Influence of Selective Laser Melting Machine Source on the Dynamic Properties of AlSi10Mg Alloy

Comparison of AlSi7Mg0.6 alloy obtained by selective laser melting and investment casting processes: Microstructure and mechanical properties in as-built/as-cast and heat-treated conditions

High Cycle Fatigue Performance of AlSi10mg Alloy Produced by Selective Laser Melting

Comparative tribological studies of additive manufactured as-built and chemically polished AlSi10Mg alloy surfaces

Effects of Heat Treatment on Microstructure and Mechanical Properties of AlSi10Mg Fabricated by Selective Laser Melting Process

Effect of cooling rates and heat treatment time on Si phase of AlSi10Mg alloy manufactured by selective laser melting: Microstructure evolution and strengthening mechanism

Mechanical Properties of AlSi10Mg Processed by Laser Powder Bed Fusion at Elevated Temperature

Selective Laser Melting Process Optimization and Mechanical Properties Evolution of AlSi10Mg by Determining Temperature of the Build Chamber using Arduino IDE and Coding Algorithm

In-situ SEM Investigation on Fatigue Behaviors of Additive Manufactured Al-Si10-Mg Alloy at Elevated Temperature

Study on the Forming Process and Properties of AlSi60 Alloy by Selective Laser Melting

POROSITY DEVELOPMENT AND CRACKING BEHAVIOR OF Al-Zn-Mg-Cu ALLOYS FABRICATED BY SELECTIVE LASER MELTING

Influence of Contour Scan Variation on Surface, Bulk and Mechanical Properties of LPBF-Processed AlSi7Mg0.6

Thermal and mechanical properties of an Al-Mg-Sc-Zr high strength alloy fabricated by selective laser melting