Abstract:Purpose The purpose of this paper is to investigate the influence of silver nanoparticle additions on the wetting properties of Sn‐Ag‐Cu (SAC) solder paste. In this investigation, the basic solder paste contained 85 wt.% of commercial Sn 96.5 Ag 3 Cu 0.5 powder (with the particle sizes in the range of 20‐38 μ m) and 15 wt.% of self‐prepared middle activated rosin flux. To this paste was added 0.5, 1, 2 and 4 wt.% of self‐prepared silver nano‐powders of different grain sizes (from 9 to 138 nm). After the pastes had stabilized, their wetting properties were tested. The main goal of these investigations was to improve the wetting properties of SAC solder paste and to find correlations between the results of the wetting of solder paste with nanoparticles on the copper substrate with the microstructure of the solder joints. Design/methodology/approach The following methods were applied for the wetting solder paste investigation: spreading on the copper substrate, contact angle measurement on the copper and wetting on a FR‐4 laminate double sided with an 18‐ μ m thick copper foil. The investigations were performed at temperatures of 220, 230, 240 and 250°C. Cross‐sectioning was performed on the solder paste after reflow on the copper substrate. For the microstructural analysis of the “nano” modified solder joints obtained at 250°C, standard metallographic procedures were applied. Changes in the microstructure, the thickness of the inter‐metallic compounds (IMCs) and their chemical compositions were observed by means of scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS). Findings As expected, a higher silver nanoparticle addition to the SAC solder paste resulted in better wetting properties on copper. The results indicated the possibility of an improvement of the reflow soldering process by using SAC solder paste with silver nanoparticles and by lowering its soldering temperature. An improvement was also observed in the wettability with a decrease in the silver nanoparticle grain size. Also, the wettability proceeded at a lower temperature (20°C lower) than that for the SAC paste, without the nano‐additives. For the 4 per cent silver nanoparticle addition, Ag 3 Sn star‐like IMCs were also found, which grew with the lowering of the silver nanoparticle grain size. Research limitations/implications Further studies are necessary for confirmation of the practical application, especially of the mechanical properties, as well as the reliability properties of the solder joints, for the chosen solder paste with silver nanoparticles. Practical implications Taking into account the wetting data, the best results of the “nano” SAC solder pastes were obtained for the highest addition of the silver nanoparticles. It was found that the spreading on copper was higher and the contact angles were lower for the SAC solder paste with 4 per cent (by wt.) of 138‐nm grain size silver nanoparticles. A comparison of SAC solder pastes with a 4 per cent silver nanoparticle addition but of a different grain size (138‐9 nm), suggested a further improvement in wetting properties with lowering of the silver nanoparticle grain size. The results suggested the possibility of an improvement in the reflow soldering process by using SAC solder paste with silver nanoparticles and by lowering its soldering temperature. Originality/value Spreading, wetting and contact angle measurement methods were used for the wetting determination of the SAC solder paste with the silver nanoparticles on copper under the same temperature conditions. Also, the microstructure of the solder joints obtained at 250°C was determined with the use of SEM and EDS methods. The results obtained made it possible to draw conclusions regarding the correlation between the output of the wetting results and the amount and the grain size of the added silver nanoparticles, and also the microstructure and thickness of the IMCs of the “nano” solder joints.

Effects of immersion silver (ImAg) and immersion tin (ImSn) surface finish on the microstructure and joint strength of Sn-3.0Ag-0.5Cu solder

Effects of Surface Finish on Sn-3.0Ag-0.5Cu Solder Joint Microstructure and Strength

Intermetallic and tensile study of the newly developed Sn-2.0Ag-0.7Cu solder with addition of 0.5 wt.% zinc

In-situ fusion process and Cu–Sn compounds evolution mechanism of nano-intermetallic compound mixed solder joints

The impact of paste alloy, paste volume, and surface finish on solder joint

Interfacial microstructure, shear strength and wettability of Ni-added Sn-0.3Ag-0.7Cu/Cu solder joint

Microstructure evolution and growth behavior of Cu/SAC105/Cu joints soldered by thermo-compression bonding

Effect of Nano-Cu 6 Sn 5 upon development mechanism of Cu–Ni–Sn compounds and mechanical characteristics for mixed solder joints

Performance and interfacial reaction mechanism of nano-IMC-mixed solder paste with variable melting point

Study of electromigration in Sn-Ag-Cu micro solder joint with Ni interfacial layer

Comparative Study of the Impurity Effect on SnAgCu and SnZn Solder Joints with Electrodeposited Cu

Effects of Joint Height on the Interfacial Microstructure and Mechanical Properties of Cu-Cored SAC305 Solder Joints

Tin Multilayer‐Aided SAC305‐Based Lead‐Free Solder Joint Interface with Cu: An Investigation of the Stress Distribution by Finite Element Analysis and Nanoindentation Studies

Effect of Ni on the Suppression of Sn Whisker Formation in Sn-0.7Cu Solder Joint

Effects of soldering temperatures and composition on the microstructures and shear properties of Sn58Bi-xSAC0307/ENIG solder joints

Silver nanoparticles effect on the wettability of Sn‐Ag‐Cu solder pastes and solder joints microstructure on copper

Origin of Primary Cu6Sn5 in Hypoeutectic Solder Alloys and a Method of Suppression to Improve Mechanical Properties

Microstructure evolution and grain refinement of ultrasonic-assisted soldering joint by using Ni foam reinforced Sn composite solder

Microstructure and mechanical properties of Cu joints soldered with a Sn-based composite solder, reinforced by metal foam

Effects of post-reflow cooling rate and thermal aging on growth behavior of interfacial intermetallic compound between SAC305 solder and Cu substrate

Effect of the addition of Cu6Sn5 nanoparticles on the growth of intermetallic compounds at the interfaces of Sn3.0Ag0.5Cu solder joints