Abstract:Few researches on high efficiency modified phosphogypsum (MPG) and its resource utilization in bulding materials. This article investigated the effects of different lower temperatures and drying times on the thermodynamic modification mechanism of macroscopic performance and microscopic structure of MPG, and investigates its application in phosphogypsum-based self-leveling mortars (PBSLM). Then, the coupling mechanism of characteristic heavy metals in the modification process (original-modification-hydration) was discussed, and the safety evaluation was conducted on the content of heavy metal elements in the sample. Data from microscopic analysis showed that with the increase of temperature and drying time, the strength of MPG blocks and the decomposition rate of dihydrate gypsum crystal both increased, while the particle size decreased. The degree of crystal decomposition becomes more complete as the temperature rises if the holding time remains constant. As well as, the MPG at 180 °C/7 h, 195 °C/7 h/10 h met the Chinese standard of " Calcined gypsum " (GB/T9776). The heavy metal elements in MPG decreased obviously, caused by the substitution solid solution formed by Ca 2+ and Fe 3+ and heavy metal ions and the adsorption of calcium sulfate hemihydrate crystals. After hydration of MPG, As and Cd increased slightly because dicalcium phosphate was insoluble in water and soluble in acid, and iron oxide reduced and dissolved Cd. Then, the ecological hazards of heavy metals in hydrated MPG after hydration were evaluated. The results showed that there was no environmental safety problem in the hydrated MPG, but the As and Cr elements in it had an acceptable carcinogenic risk through oral intake. Based on ensuring the safety of MPG, MPG powder was used in PBSLM. The research demonstrates that the basic mechanical properties of the PBSLM produced, when the MPG powder content is 330 g, and cement is 40 g are the best. The heavy metal aqueous solution's leaching amount is lower than China's national standard limit value. (30min fluidity, 24 h-flexural and compressive strength were 154 mm, 5.7 MPa and 10.6 MPa). Finally, based on this research, a set of general evaluation system for safe utilization of solid waste was established according to national standards. This provides theoretical support for the research of heavy metal in PG at low temperature and the ways of harmless and resource utilization.

Utilization of high-volume phosphogypsum in artificial aggregate by compaction granulation: effects of muck on physical properties, strength and leaching stability

Reuse of phosphogypsum pretreated with water washing as aggregate for cemented backfill

Mechanical properties of phosphogypsum-soil stabilized by lime activated ground granulated blast-furnace slag

Utilization of untreated-phosphogypsum as filling and binding material in preparing grouting materials

A new eco-friendly concrete made of high content phosphogypsum based aggregates and binder: Mechanical properties and environmental benefits

Mechanical properties and soluble phosphorus solidification mechanism of a novel high amount phosphogypsum-based mortar

Preparation of artificial aggregate to be used in the asphalt mixture

Physical properties, strength, and impurities stability of phosphogypsum-based cold-bonded aggregates

Study on preparation of inorganic binder stabilized material with large dosage of phosphogypsum

Properties of Cemented Filling Materials Prepared from Phosphogypsum-Steel Slag-Blast-Furnace Slag and Its Environmental Effect

Enhanced Strength and Fluoride Ion Solidification/stabilization Mechanism of Modified Phosphogypsum Backfill Material

Sustainable Utilization of Phosphogypsum in Multi-Solid Waste Recycled Aggregates: Environmental Impact and Economic Viability

The Influence Mechanism of Molar Ratio on the Performance of Phosphogypsum-Modified Geopolymer Material

Utilizing Raw Phosphogypsum to Prepare One-Part Geopolymer: Mechanical Properties, Optimization, and Hydration Mechanisms

Immobilization of phosphogypsum for cemented paste backfill and its environmental effect

Application of phosphogypsum to solidification of silty soil: Mechanical properties and microstructure

Reuse of Pretreated Red Mud and Phosphogypsum as Supplementary Cementitious Material

Characteristic pollutant purification analysis of modified phosphogypsum comprehensive utilization

Modification mechanism, heavy metal coupling and ecological security risk assessment of phosphogypsum utilization in self-leveling mortar

Influence of partial cement substitution by ground blast furnace slag on the mechanical properties of phosphogypsum cemented backfill