Abstract:In this paper, the effects of different rare earth elements (La, Ce, Sm and Er) on the microstructure and mechanical properties of Al-6.7Zn-2.6 Mg-2.0Cu-0.1Zr alloys have been investigated. The results show that the addition of rare earth elements, especially those with a higher atomic number (La < Ce < Sm < Er), could effectively reduce the alloy grain size. Rare earth elements form Al11La3, Al4Ce, Al10Cu7Sm2 and Al8Cu4Er phases in the alloy. After being rolled, the small rare earth phases could pin the grain boundaries, inhibit recrystallization, and refine the structure during solid solution treatment. Moreover, the rare earth atoms would provide more nucleation sites for the precipitation of the η' phase to make it smaller during the aging treatment. Therefore, the rare earth elements can significantly improve the mechanical properties of the alloy through grain refinement and precipitation strengthening. Because Er has a lower solid solubility in Al matrix than other elements, and can form Al3 (Er, Zr) phase, this phase can effectively inhibit recrystallization behavior. Therefore, among all the studied rare earth elements, Er has the strongest strengthening effect, which increases the tensile strength and yield strength of the alloy by 40Mpa and 29Mpa, respectively. The Sm-containing alloy acquire more fine recrystallized grains after solid solution, so that the elongation of the alloy is increased to 14.3%, and its plasticity is the best.

Effect of Rare Earth Elements on the Microstructural and Mechanical Properties of ZK60 Alloy after T5 Treatment

Effect of Addition of Rare Earth Elements on the Microstructure, Texture, and Mechanical Properties of Extruded ZK60 Alloy

Processing Maps and Hot Compression Behaviors of ZK60 Alloy After Adding Different Rare Earth Elements

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Modification of the Tensile Performance of an Extruded ZK60 Magnesium Alloy with the Addition of Rare Earth Elements

Effect of Ce and Y on Microstructures and Properties of Al-11.0Zn-3.1Mg-1.22Cu-0.1Sr-0.2Zr-0.1Ti Alloy

Effect of adding Y and Ce on corrosion behaviour of the extruded ZK60 magnesium alloy

Effect of Y on Age Hardening Response and Mechanical Properties of Mg-xY–1.5LPC −0.4zr Alloys

The Effect of Precipitates on the Mechanical Properties of ZK60-Y Alloy

Effect of Ce Microalloying on Microstructure and Mechanical Properties of Extruded Mg–10Gd–0.5Zr Alloy

Effect of rare earth Ce and Y on microstructure and viscosity of ZL114A alloy

Study on Phases Formation and Modification Ability of Rare Earth Elements La, Ce, Sm and Er in Al–Zn–Mg–Cu–Zr Alloy

Effects of Rare Earth Elements and Ti on Microstructure and Properties of ZM5 Magnesium Alloy

Microstructure and mechanical properties of extruded ZK60 magnesium alloy containing rare earth

Effect of Ce Addition on Modifying the Microstructure and Achieving a High Elongation with a Relatively High Strength of As-Extruded AZ80 Magnesium Alloy

Effect of Cerium on Microstructures and Mechanical Properties of Az61 Wrought Magnesium Alloy

Effects of Ce Addition on Microstructure and Properties of Mg-Gd-Y-Nd-Zr Alloy

Effect of Y and Ce Micro-alloying on Microstructure and Hot Tearing of As-Cast Al–Cu–Mg Alloy

Effect of combined addition of Zr, Ti and Y on microstructure and tensile properties of an Al-Zn-Mg-Cu alloy

Effect of Micro-alloyed Ce on the Microstructure and Mechanical Properties of Mg-Gd-Zr Alloy

Effects of yttrium on microstructure and mechanical properties of hot-extruded Mg–Zn–Y–Zr alloys