Abstract:We describe here the relationship between grain structure, deformation mechanism and fracture characteristics in an austenitic stainless steel. This was accomplished using the novel concept of phase reversion that enabled a wide range of grain size from nanograined/ultrafine grained (NG/UFG) to coarse-grained (CG) regime to be obtained in a single material through change in temperature-time annealing sequence. In the NG/UFG structure, a marked increase in abundance of stacking faults (SFs) and twin density with strain was observed that led to a decrease in the average spacing between adjacent SFs, thus converting stacking faults into twins. Twinning in NG/UFG structure involved partial dislocations and their interaction with the grain boundaries, including SF overlapping and the coordinated nucleation of partial dislocations from the grain boundaries. The plastic zone in the NG/UFG structure resembled a network knitted by the intersecting twins and SFs. With SFE ~30 mJ/m2, the minimum stress for twin nucleation was ~250 MPa for the experiment steel and the corresponding optimal grain size (dop) wa ~120 nm. In contrast, in the CG structure, strain induced martensite formation was the deformation mechanism. The difference in the deformation mechanism led to a clear distinction in the fracture behavior from striated fracture in high strength-high ductility NG/UFG alloy to microvoid coalescence in the low strength-high ductility CG counterpart. The underlying reason for the change in fracture behavior was consistent with change in deformation mechanism from nanoscale twinning in NG/UFG alloy to strain-induced martensite in the CG alloy, which is related to change in the stability of austenite with grain size. An analysis of critical shear stress required to initiate twinning partial dislocations in comparison to that required to nucleate shear bands is presented. The appearance of striated fracture in the NG/UFG alloy suggests a quasi-static step wise crack growth process.

Operando Study of Structural Changes in High-Manganese Steel Under Dry Friction

A Study of Friction-Induced Martensitic Transformation for Austenitic Manganese Steel

An Investigation of Friction Coefficient on Microstructure and Texture Evolution of Interstitial-Free Steel during Warm Rolling and Subsequent Annealing

A Study On The Dynamic Characteristics Of Abrasion For High-Chromium Alloys

Changes in the Phase Composition of High-Manganese Steels during Tensile Deformation

Evolution of Microstructure and Deformation Mechanisms in a Metastable Fe42Mn28Co10Cr15Si5 High Entropy Alloy: A Combined In-Situ Synchrotron X-ray Diffraction and EBSD Analysis

Thermal deformation behavior and microstructure evolution of Fe−8.5Mn−1.5Al light−weight medium manganese steel

Formation of Nanocrystallized Structure in Worn Surface Layer of T10 Steel Against 20crmnti Steel During Dry Rubbing

Microstructure evolution and mechanical properties of friction welded IN713LC and AISI 4140

Atomic diffusion of gradient ultrafine structured surface layer produced by T10 steel rubbing against 20CrMnTi steel

In-situ neutron diffraction investigation of two-stage martensitic transformation in a 13%Mn steel with serrated deformation

Deformation mechanism and microstructure evolution of medium-Mn AHSS under various loading conditions

Microstructural Dependence of Anisotropic Fracture Mechanisms in Cold-Drawn Pearlitic Steels

Internal Friction Behavior Associated with Martensitic Decomposition in Low-carbon Dual-phase Steel

The significance of deformation mechanisms on the fracture behavior of phase reversion-induced nanostructured austenitic stainless steel

Quasi-in-situ observations of crack propagation and microstructure evolution of high manganese austenitic steel at −196 °C

Microstructure evolution and mechanical behavior of Fe-Mn-Al-C low-density steel upon aging

Microstructure evolution in high-pressure phase transformations of CrFeNi and CoCrFeMnNi alloys

Coupling Friction and Deformation Experiment

The In Situ Observation of Phase Transformations During Intercritical Annealing of a Medium Manganese Advanced High Strength Steel by High Energy X-Ray Diffraction

Grain coarsening of nano laminated structure in martensite steel under sliding wear