Abstract:Manganese stabilizes austenite and reduces stacking fault energy in face‐centered cubic (FCC) structures, facilitating phase transformation in FeCrMn AISI 201 steel during cold drawing. This study examines phase transformation from FCC to hexagonal close‐packed and body‐centered cubic structures, using X‐ray diffraction and electron backscatter diffraction. Results show that 50% true strain optimally balances strength and ductility, with significant increases in yield strength and ultimate tensile strength but reduced elongation. Manganese stabilizes the austenite and reduces the stacking fault energy in face‐centered cubic (FCC) structures, promoting the formation of hexagonal and cubic structures. This study investigates the phase transformation and mechanical behavior of extremely low‐carbon FeCrMn austenitic stainless AISI 201 steel subjected to cold drawing in three stages, ultimately reaching a true strain of 0.93. The objective is to examine the transformation from the parent FCC structure to hexagonal close‐packed and body‐centered cubic structures as a combination of transformation‐induced plasticity and twinning‐induced plasticity phenomena. X‐ray diffraction and electron backscatter diffraction analyses are utilized to investigate phase transformations under significant plastic deformation and the crystallographic orientation relationships between phases. Additionally, tensile and hardness tests are performed to assess the impact of plastic deformation on mechanical properties. Results indicate that a true strain of 50% is optimal for balancing strength and ductility in CrMnFe austenitic stainless steel. After applying a true strain of ε1 = 26.7%, yield strength (YS) increases by 192% and ultimate tensile strength (UTS) by 35%, while elongation reduces by 41%. With a further strain of ε2 = 57.5%, YS increases by 71% and UTS by 44%, but elongation drastically decreases by 94%. Applying the final strain of ε3 = 94.0%, YS and UTS only increase by 3% and 2%, respectively, while elongation further reduced by 40%. These findings suggest that a true strain of 50% shall be considered the maximum reduction for maintaining a balance between strength and ductility in CrMnFe austenitic stainless steel.

Changes in the Phase Composition of High-Manganese Steels during Tensile Deformation

Deformation Behavior and Microstructure of Low Carbon High Manganese Steels in Tensile Strain

Martensitic Phase Transformation from Non-isothermally Deformed Austenite in High Strength Steel 22Simn2tib

Effect of Non-Isothermal Deformation of Austenite on Phase Transformation and Microstructure of 22simn2tib Steel

Effect of uniaxial compression on the microstructural evolution and magnetic properties of 20Mn23AlV non-magnetic structural steel

Phase Transformation and Mechanical Properties of G Phase (mn6ni16si7) in Mn- Ni-Si Model Alloys after 1,000°C Annealing

Effect of non-isothermal deformation of austenite on ferrite transformation behavior studied by in-situ neutron diffraction

Tensile Deformation Behavior of High Strength Anti-Seismic Steel with Multi-Phase Microstructure

Retained Austenite Transformation and Portevin–Le Chatelier Effect in 44CrMn2Si2Mo Steel under Tension

Operando Study of Structural Changes in High-Manganese Steel Under Dry Friction

Influence of Cold Drawing on Phase Transformation and Tensile Properties of FeCrMn Austenitic Stainless Steel 201

An Investigation on Microstructure Evolution and Deformation Mechanism of Ti–5Al–5Mo–5V–1Cr–1Fe Alloy During In-Situ Tensile

A Study of Friction-Induced Martensitic Transformation for Austenitic Manganese Steel

Influence of Quenching and Partitioning Parameters on Phase Transformations and Mechanical Properties of Medium Manganese Steel for Press-Hardening Application

Influence of deformation on the structure and the mechanical properties of a high-entropy Fe25Cr20Ni20Co10Mn15Al10 alloy

Tuning mechanical behavior and deformation mechanisms in high-manganese steels via carbon content modification

Changes in Mechanical Properties of Ultrahigh Strength Nanostructured Steel Resulting from Repeated High Strain Rate Deformation

In-situ neutron diffraction investigation of two-stage martensitic transformation in a 13%Mn steel with serrated deformation

Analysis of phase transformation thermodynamics and kinetics and its relationship to structure-mechanical properties in a medium-Mn high strength steel

Quantitative Analysis of the Micromechanical Behavior and Work Hardening in Fe-0.1C-10Mn Steel Via In-Situ High-Energy X-ray Diffraction

High deformation ability induced by phase transformation through adjusting Cr content in Co-Fe-Ni-Cr high entropy alloys