Abstract:High-pressure-torsion (HPT) processing introduces a large density of dislocations that form sub-grain boundaries within the refined nano-scale structure, leading to changes in precipitate morphology compared to hot-rolled maraging steels. The impact of such nanostructuring on the deformation and fracture micro-mechanisms is being reported for the first time usingin situcharacterization techniques along with transmission electron microscopy and atom probe tomography analysis, in this study. Digital image correlation has been used to quantify the full field strain maps in regions of severe strain localization as well as to determine the fracture toughness through critical crack tip opening displacements. It is seen that the phenomenon of planar slip leads to strain softening under uniaxial deformation and to crack branching under a triaxial stress state in hot rolled maraging steels. On the other hand, nano-structuring after HPT processing creates a large number of high angle grain boundaries as dislocation barriers, leading to strain hardening under uniaxial tension and nearly straight crack path with catastrophic fracture under triaxial stress state. Upon overaging, the hot-rolled sample shows signature of transformation induced plasticity under uniaxial tension, which is absent in the HPT processed overaged samples, owing to the finer reverted austenite grains containing higher Ni concentration in the latter. In the overaged fracture test samples of both the hot-rolled and HPT conditions, crack tips show a signature of strain induced transformation of the reverted austenite to martensite, due to the accompanying severe strain gradients. This leads to a higher fracture toughness even while achieving high strengths in the overaged conditions of the nanocrystalline HPT overaged samples. The results presented here will aid in design of suitable heat treatment or microstructure engineering of interface dominated nano-scale maraging steels with improved damage tolerance.

Changes in Mechanical Properties of Ultrahigh Strength Nanostructured Steel Resulting from Repeated High Strain Rate Deformation

Estimation of Residual Stresses by Nanoindentation in an Experimental High Strength Microalloyed Steel Subjected to Rapid Thermal Cycles

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

Effect of cyclic straining at elevated-temperature on static mechanical properties, microstructures and fracture behavior of nickel-based superalloy GH4145/SQ

An Investigation of the Effect of High-Temperature Cyclic Straining and Creep Loading on Tensile Mechanical Properties of GH4145/SQ Alloy

Multi-scale Deformation Behavior Investigation of 18cr–8ni Austenitic Steel Subjected to Low-Cycle Fatigue Loading

Effect of High Temperature Exposure and Strain Rate on Mechanical Properties of High-Strength Steel Rebars

Research on the thermal plasticity of the 18Mn-18Cr-0.77N-2Mo high nitrogen austenitic stainless steel

Deformation behavior and microstructure evolution of 300M ultrahigh strength steel subjected to high strain rate: an analytical approach

Tensile properties and strain hardening mechanism of Cr-Mn-Si-Ni alloyed ultra-strength steel at different temperatures and strain rates

Shaping Microstructure and Mechanical Properties of High-Carbon Bainitic Steel in Hot-Rolling and Long-Term Low-Temperature Annealing

High-entropy CoCrFeMnNi Alloy Subjected to High-Strain-rate Compressive Deformation

Study on dynamic recrystallization of ultra-high strength 22MnB5 steel during hot rolling

Yielding Behavior and Strengthening Mechanisms of a High Strength Ultrafine‐Grained Cr–Mn–Ni–N Stainless Steel

Micro-mechanisms of failure in nano-structured maraging steels characterised through in situ mechanical tests

Notably Accelerated Nano-Bainite Transformation via Increasing Undissolved Carbides Content on GCr15Si1Mo Bearing Steel

Texture Analyses and Mechanical Behavior of a High-Mn Steel Subjected to Different Pass Number of Simple Shear

Hot Deformation Behaviour of Additively Manufactured 18Ni-300 Maraging Steel

Effects of Mechanical Deformation on Dislocation Density and Phase Partitioning in 4130 Steel

Dynamic Compressive Mechanical Behavior and Microstructure Evolution of Rolled Fe-28Mn-10Al-1.2C Low-density Steel

High Strain Rate Behaviour of Stainless-Clad Bimetallic Steel