Abstract:Stretchable nanofiber fabrics refer to fabrics woven with elastic nanofibers, and nanofibers are defined as fibers with a diameter less than 100 nm. For example, nanofibers are implanted on the surface of the fabric to form a stable gas film. The biphobic interface can be used for the purification and filtration of sports equipment, chemical products, medical drugs and other products. The development of sports is increasingly dependent on science and technology, and stretchable nanofibers, as an emerging field of science and technology, are undoubtedly widely used in sports materials. This article first explains the role and background of stretchable nanofiber fabrics in sports equipment, and explains related methods, such as the slurry method for preparing rubber thermally conductive composites in sports equipment, and testing the thermal conductivity and thermal conductivity of composite materials. Diffusion coefficient, density and specific heat capacity; and then explain the polyrhodanine coating method, coating stretchable nano fabric, testing its mechanical properties and thermal conductivity, calculating the agglomeration phenomenon of particles in the rubber, you can get the wrapped PRh- The effect of BNNSs' self-aggregation is suppressed; then the stress and strain of the nano-layer are tested using electrospinning technology, that is, the mechanical properties; finally, the tensile test of carbon fiber three-directional nano-fabric sports composite material is carried out, the tensile model is set, and the test is performed The strain and deformation in the stretching process at 0° and 90°, the load change and tensile elongation at break of the two are analyzed, the tensile attenuation rate in the 0° direction is lower than the attenuation rate in the 90° direction, 0° The tensile elongation at break in the direction of 90° is less than the tensile elongation at break in the direction of 90°, and one of the differences is judged that there is no carbon nanofiber on the parallel load in the 90° direction. The application of the above, taking bicycle tires and golf clubs as examples, combined with the average expected lift and 90° three-dimensional weaving method, the tensile strength direction can be obtained. This nanofiber three-dimensional weaving method has a higher tensile load than the composite material in the 90° direction. The average expected improvement of the ordinary weaving method is 36.1%, and the use of 90° three-dimensional nano fabric materials can improve the performance of sports equipment under this material by 16.9% to 51.8%.

Preparation of Composite Multi-Iron Material 0.2NiFe2O4/0.8BaTiO3 and Its Application in Sports Practice

Influence of Polymer Properties on Sports Equipment Performance from the Perspective of Composite Materials

Discuss on Preparation Method of Composite Sports Equipment Based on Stretchable Nanofiber Fabric

Fiber Nanocomposite Material Used in College Tennis Training and Preparation Method Thereof

Preparation Of Fine-Grained Multiferroic Batio3-(Ni0.5zn0.5) Fe2o4 Ceramic Composites

Study of the Mechanical Property of Magnetite/ Hydroxyapatite/ Chitosan Nano-Composite

Ferroelectricity and Ferromagnetism in Fine-Grained Multiferroic Batio3/(Ni0.5zn0.5)Fe2o4 Composites Prepared by A Novel Hybrid Process

Polyurethane Elastomer Layered Nanocomposite Material for Sports Grounds and the Preparation Method Thereof

High-performance aluminum/carbon composite material and preparation method thereof

Preparation and Interface Investigation of Fe/Al2o3p Composite Activated by Ni and Ti

Textured Hybrid Nanocomposite Coatings for Surface Wear Protection of Sports Equipment

Highly Anisotropic, Thermally Conductive, and Mechanically Strong Polymer Composites with Nacre-like Structure for Thermal Management Applications

Dual bionics of structure and preparation: Gradient architectured carbon/ceramic composite as light as water but bearing ultra-high temperature max to 2500 °C

Preparation and Characterization of Iron/Titanium-Oxide Composite Particles

Preparation method of composite material

Achieving the Superior Abrasive Wear Resistance in ZTAP/Fe Composites from the Theoretical Calculations Guided Designing of Metallurgical Interface Transition Layer

Preparation and properties of composite manganese/fluorine coatings on metallic titanium

Polyacrylonitrile/multi-walled carbon nanotubes/polyurethane electrospun nanofiber membranes for sports equipment

Biomedical Performances of NiTi Alloy and Its Biomedical Applications

High damage-tolerance nacre-inspired TiB 2 /Al-Cu composites with adjustable mechanical performance based on heat-treatment condition tuning

Fabrication and High-Temperature Tribological Properties of Self-Lubricating NiCr–BaMoO 4 Composites