Abstract:Ceramic-reinforced aluminum-based composites are ideal materials for lightweight structural parts. However, as the content of the ceramic reinforcement phase increases, the toughness of the composites will decrease, resulting in a decrease in the safety of the composites during service. Therefore, how to achieve the matching of high strength and toughness of composite materials is a problem that has always existed in the preparation of ceramic reinforced aluminum matrix composites. According to the idea of bionics, the nacre-inspired TiB2/Al-Cu composites with different ceramic initial solid content (20vol.%, 30vol.%, 40vol.%) were successfully prepared by freezing casting and pressure infiltration. The microstructures and mechanical properties of nacre-inspired TiB2/Al-Cu composites were studied by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and mechanical testing. The experimental results show that with the increase of the initial solid content of the ceramic, the thickness of the ceramic sheet in the composite material increases, while the thickness of the metal sheet layer decreases. The compressive strength of the composite material is improved, but the bending strength and fracture toughness decrease. The nacre-inspired TiB2/Al-Cu composites with 20vol.% ceramic initial solid content has the better fracture toughness, reaching 20.59±1.5 MPa·m1/2; The nacre-inspired TiB2/Al-Cu composites with 40vol.% ceramic initial solid content has the better compressive strength, reaching 670±20 MPa. This is mainly because as the initial solid content of the ceramic in the composite material increases, the nacre-inspired composite material are more prone to interface delamination, the toughening effect of the layered composite material through alloy plastic deformation is weakened; at the same time, the toughening effect of crack deflection, interface peeling, and crack branching is reduced.

High damage-tolerance nacre-inspired TiB 2 /Al-Cu composites with adjustable mechanical performance based on heat-treatment condition tuning

High Damage-Tolerance Nacre-Inspired TiB2/Al-Cu Composites with Adjustable Mechanical Performance Based on Heat-Treatment Condition Tuning

Fabrication and Characterisation of Alumina/aluminium Composite Materials with a Nacre-Like Micro-Layered Architecture

Microstructure and Mechanical Properties of Nacre-Inspired TiB2/Al-Cu Composites

Nacre-inspired Ti (C, N)/Al–Cu Composites with High Damage Tolerance and Wear Resistance Prepared by Freeze and Squeeze Casting

Microstructures and Mechanical Properties of High-Performance Nacre-Inspired Al-Si/TiB2 Composites Prepared by Freeze Casting and Pressure Infiltration

High Temperature Mechanical Properties and Tribological Behavior of Nacre-Inspired Ti (C, N)/Al-Cu Composites

Nacre-like Hybrid Aluminum-Matrix Composite with Simultaneously Enhanced Strength and Toughness

Optimization of the microstructure, mechanical properties, and wear resistance of nacre-inspired TiB2/Al-Cu composites via gelatin addition

Bioinspired nacre-like 2024Al/B4C composites with high damage tolerance

Developing nacre-inspired laminate-reticular 2024Al/B4C composites with high damage resistance by adjusting compositional wettability

High damage-tolerance bio-inspired B4C/2024Al composites with adjustable mechanical performance by tuning ceramic thickness

Developing High-Performance Laminated Cu/TiC Composites Through Melt Infiltration of Ni-doped Freeze-Cast Preforms

Corrosion Behavior of Nacre-Inspired (TiBw-TiB2)/Al Composites Fabricated by Freeze Casting

Synthesis of damage-tolerant Cu-matrix composites with nacre-inspired laminate-reticular hierarchical architecture via tuning compositional wettability

Optimization of the Microstructure, Mechanical Properties, and Wear Resistance of Nacre-Inspired TiB 2 /Al-Cu Composites Via Gelatin Addition

Cost-effective Fabrication of Bio-Inspired Nacre-Like Composite Materials with High Strength and Toughness

Influence of Matrix Property and Interfacial Reaction on the Mechanical Performance and Fracture Mechanism of TiC Reinforced Al Matrix Lamellar Composites

Performance Assessment Of Tinbf/Tial Composites With Different Fiber Structural Characteristics

Microstructures and Mechanical Characterizations of High-Performance Nacre-Inspired Al/Al2O3 Composites

Processing and Mechanical Properties of Lamellar-Structured Al–7Si–5Cu/TiC Composites