Abstract:<p>The high strength Al–Zn–Mg plates were processed by combing the hot extrusion and cold rolling. Then, both the artificial aging and annealing were conducted to make a comparative study on the microstructure, mechanical properties, and corrosion resistance. The aged samples were composed of near-equiaxed grains attributed from the static recrystallization during solution process, and owned the main textures of Cube, Goss, Copper, S, and Brass. The precipitate followed the sequence of SSS → GP zone → η′ phase → η phase. With the increase of aging time, the grain boundary precipitations (GBPs) became coarse and discontinuous, and the width of precipitate free zones (PFZs) also increased. In annealed samples, the coarse and elongated grains were finally formed, and the volume fraction of recrystallization textures increased with the extension of annealing time. Moreover, the density of dislocations and the number of MgZn<sub>2</sub> phase were both reduced during annealing. The tensile strength along 0° with rolling direction was always the highest in all aged and annealed samples, and the elongation achieved the highest values along 45°. Long-time aging slightly improved the planar anisotropy, while long-time annealing greatly improved the planar anisotropy. The peak aged sample showed a ductility loss of 21.96% during the slow strain rate test in 3.5 wt% NaCl, and a maximum depth of 214.59 μm in intergranular corrosion test. Compared to the annealed sample, the aged one exhibited the worse corrosion resistance due to the wide PFZs and continuously distributed GBPs.</p>

Corrosion behavior of Mg-5.7Gd-1.9Ag Mg alloy sheet

Effects of solid solution and aging process on microstructure and mechanical properties of Mg-Gd-Y alloy

Comparative Study on Corrosion Behavior of As-Cast and Extruded Mg–5Y–7Gd–1Nd–0.5Zr Alloy in 5% NaCl Aqueous Solution

Comparative Study on Corrosion Behavior and Mechanism of As-Cast Mg–Zn–Y and Mg–Zn–Gd Alloys

Surface microstructure and corrosion resistance characterization of Mg-based amorphous alloys

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Investigation of Evolution of Microstructure, Mechanical Properties, and Corrosion Resistance of Novel Al-Mg-Si-Ag Alloy

Enhancing Strength-Ductility Synergy and Corrosion Residual Strength of Hot-Rolled Mg-2Zn-0.85Y Alloy

High corrosion resistance and weak corrosion anisotropy of an as-rolled Mg-3Al-1Zn (in wt.%) alloy with strong crystallographic texture

Synchronous improvement in mechanical properties and corrosion resistance of Mg-Gd-Ag-Zr alloy through nanoprecipitates

Response of mechanical properties and corrosion behavior of Al–Zn–Mg alloy treated by aging and annealing: A comparative study

Investigation of Corrosion Behaviors of Mg–6Gd–3Y–0.4Zr Alloy in NaCl Aqueous Solutions

Study of the corrosion mechanism of Mg–Gd based soluble magnesium alloys with different initial texture states

Enhanced age-hardening response and mechanical properties of the Mg-Gd-Y-Zn-Zr alloy by trace Ag addition

Effects of micro-alloying Ag on microstructure, mechanical properties and corrosion behavior of extruded Mg-2Zn-0.2Ca-xAg alloys

Improving Aging Behavior and Corrosion Resistance of Mg-5Ga Alloy by Ca Alloying

Comparison of the Corrosion Behaviors of Mg–Gd–Y–Zn–Zr Alloys Fabricated by Different Preparation Methods

Corrosion Behavior of Mg-Zn-Y-Zr Alloys in Nacl Solution

Roles of micro-alloyed Y and Gd in improving the corrosion resistance and mechanical properties of pure Mg

Study on the Microstructure and Corrosion Behavior of Mg–(4 − X)gd–xy–2zn (x = 0, 2, 4 Wt%) Alloy

Achieving High Strength and High Conductivity of Cu-6 wt%Ag Sheets by Controlling the Aging Cooling Rate