Abstract:This study aimed to investigate the mechanical behavior of an environmentally friendly granulated blast furnace slag-based geopolymer matrix reinforced with modified multi-walled carbon nanotubes (MWCNTs). The modified MWCNTs were obtained using a modification method combining nitric acid and sulfuric acid and were then dispersed using sodium dodecylsulfate (SDS) as a dispersant. Two types and three concentrations of MWCNTs were mixed directly into the aqueous solution, sonicated, and then mechanically mixed with waste granulated blast furnace slag to form the geopolymer matrix. Raman and Fourier transform infrared (FT-IR) spectroscopy were used to evaluate the ordered structure and crystallization degree of the modified MWCNTs. Then, the dispersity of the modified MWCNTs was characterized using transmission electron microscopy (TEM). The compressive and bending strengths were measured to evaluate the mechanical behavior of specimens. Moreover, the polycondensation products, polycondensation degree, pore structure, and microscopic morphology of the geopolymer matrix were analyzed using X-ray diffraction (XRD), FT-IR spectroscopy, nuclear magnetic resonance (NMR), mercury intrusion porosimetry (MIP), and field emission scanning electron microscopy with energy dispersive X-ray spectroscopy (FESEM-EDS). The experimental results showed that the incorporation of 0.1% functionalized MWCNTs had an optimal influence on the fluidity and mechanical behavior. The slump diameters of geopolymers with 0.1% functionalized MWCNTs with and without SDS were increased by 16.3% and 23.5%, respectively, compared with the reference geopolymer matrix. For geopolymer matrix samples at a curing age of 28 d, the compressive strength of geopolymers with 0.1% functionalized MWCNTs with and without SDS were increased by 16.3% and 17.6%, respectively. For the bending strength, the corresponding increases were 17.6% and 18.7%, respectively. It was found that functionalized MWCNTs could increase the degree of polycondensation, leading to a more traditional amorphous N-A-S-H phase, a finer C–S–H phase, more Q4 (2Al) and Q4 (3Al), and lower porosity. In addition, the propagation of micro-cracks in the geopolymers was inhibited by the incorporation of functionalized MWCNTs.

Effect of different curing methods on the preparation of carbonized high-titanium slag based geopolymers

Microwave-thermal-assisted curing method on geopolymer preparation from Panzhihua high-titanium slag by alkali activation

Effect of Curing Temperature on High-Strength Metakaolin-Based Geopolymer Composite (HMGC) with Quartz Powder and Steel Fibers

Study the Mechanical Properties of Geopolymer under Different Curing Conditions

Effect of multi-walled carbon nanotubes on durability of high-strength slag-based geopolymer

Preparation and curing method of red mud-calcium carbide slag synergistically activated fly ash-ground granulated blast furnace slag based eco-friendly geopolymer

The Effect of Different Curing Temperatures on the Properties of Geopolymer Reinforced with Micro Steel Fibers

Performance Characteristics of Micro Fiber-Reinforced Ambient Cured One-Part Geopolymer Mortar for Repairing

Geopolymer bricks prepared by MSWI fly ash and other solid wastes: Moulding pressure and curing method optimisation

Preparation and Properties of Porous Concrete Based on Geopolymer of Red Mud and Yellow River Sediment

Effect of curing temperature on geopolymerization of metakaolin-based geopolymers

Strength and microstructural analysis of geopolymer prepared with coal-based synthetic natural gas slag

Study on High-Ductility Geopolymer Concrete: The Influence of Oven Heat Curing Conditions on Mechanical Properties and Microstructural Development

Influence of modified multi-walled carbon nanotubes on the mechanical behavior and toughening mechanism of an environmentally friendly granulated blast furnace slag-based geopolymer matrix

Effect of Organic Polymers on Mechanical Property and Toughening Mechanism of Slag Geopolymer Matrix

Early Hydration Characteristics of Complex Binder Containing Slag under High Temperature

Study on the Curing and Foaming of Surfactant-Modified Geopolymer Gels Based on Ash and Slag Waste from Coal Combustion

Investigation of the Mechanical Properties of Quick-Strength Geopolymer Material Considering Preheated-to-Room Temperature Ratio of Sand, Na2SiO3-to-NaOH Ratio, and Fly Ash-to-GGBS Ratio

Effect of Elevated Temperature on Mechanical Properties of High-Volume Fly Ash-Based Geopolymer Concrete, Mortar and Paste Cured at Room Temperature

Preparation and electromagnetic wave absorption characteristics of multifunctional light-weight high titanium slag-based foam geopolymer

Effect of High-Temperature Curing Methods on the Compressive Strength Development of Concrete Containing High Volumes of Ground Granulated Blast-Furnace Slag