Abstract:Vat photopolymerization (VPP) 3D printing of ceramics normally uses ceramic slurries directly made of the target ceramic powder. It may become challenging when the ceramic powders are difficult-to-make and thus are expensive or rarely accessible. We have previously proposed a generative shaping and material-forming (GSM) 3D printing strategy, which involves the use of low-cost multi-component inorganic ceramic precursors as powder sources. The shaping of complex structures was realized through VPP, followed by reaction sintering to form the target ceramic material. In the current study, as a step further, ceramic (Li2CO3) and polymer (methyl polysiloxane) combined precursors were employed as an alternative material source for the first time to go through the 3D printing and reaction sintering processes, complementing the application range of the proposed GSM strategy. The slurry formulation and printability, the sinterability of the printed parts and the microstructures and mechanical performance of the sintered parts were characterized and optimized in accordance with the ingredient contents, particularly the stoichiometric ratios of Si:Li in the precursors. As a result, complex-structured Li4SiO4 ceramics with high purity were fabricated based on the use of Li2CO3 ceramic and Si-rich polymer as precursors. Through the advanced characterization and analysis of material phase and microstructural evolution, it was found that the fabricated complex-structured Li4SiO4 ceramics based on a precursor slurry with a solid content of 40 vol%, a Si:Li ratio of 1:2.5, and a sintering temperature of 850 °C showed a high phase purity of 97.23% and a compressive strength of 15.24 ± 0.33 MPa, with a skeleton’s relative density of 65.31% is achieved. The results showed greatly enhanced strength at much higher porosities, which might be advantageous and beneficial to structure engineering for mechanical enhancement and the improvement of tritium release effectiveness. Compared with the previous study using multi-component ceramic powder precursors, the ceramics prepared in this study exhibited enhanced microstructural stability and higher phase purity with an advantageously lower sintering temperature. Further analysis revealed that compared with the high temperature solid-state reaction of multi-component ceramic powder precursors, the involvement of the Si-rich polymer precursor enabled the more efficient and complete synthesis of Li4SiO4 as a result of the accelerated covering and cleavage of Si–O–Si bonds on the Li2CO3 particles at a much lower temperature. The present work suggests that the GSM strategy using combined ceramic and polymer precursors as proposed in this study is a promising alternative method to produce high quality Li4SiO4 components with complex structures.

3D-printing of polymer‐derived SiCN ceramic matrix composites by digital light processing

Three-dimensional printing of SiCN ceramic matrix composites from preceramic polysilazane by digital light processing

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Carbon nanotubes as light absorbers in digital light processing three-dimensional printing of SiCN ceramics from preceramic polysilazane

Silicon carbide whiskers reinforced SiOC ceramics through digital light processing 3D printing technology

Stereolithography-based additive manufacturing of lightweight and high-strength Cf/SiC ceramics

Fabrication and characterization of carbon fiber reinforced SiC ceramic matrix composites based on 3D printing technology

High strength and microwave-absorbing polymer-derived SiCN honeycomb ceramic prepared by 3D printing

Enhanced Molding and Mechanical Properties of SiC-based Ceramic Lattice Structures Via Digital Light Processing

Optimizing the properties of vat photopolymerization 3D-printed SiC ceramics by multi-infiltration

Direct Ink Writing of Chopped Carbon Fibers Reinforced Polymer-derived SiC Composites with Low shrinkage and High Strength

Additive manufacturing of polymer‐derived ceramic matrix composites

Influence of the content of polymethyl methacrylate on the properties of porous Si3N4 ceramics fabricated by digital light processing

Microstructure and mechanical properties of continuous carbon fiber-reinforced SiC ceramic composite fabricated by direct ink writing

Microstructure and mechanical properties of 3D Cf/SiBCN composites fabricated by polymer infiltration and pyrolysis

Preparation of Cf/Si3N4 composites based on vat photopolymerization combined with precursor infiltration and pyrolysis

In situ formation of Si3N4–SiC nanocomposites through polymer-derived SiAlCN ceramics and spark plasma sintering

Preparation of low residual silicon content Si-SiC ceramics by binder jetting additive manufacturing and liquid silicon infiltration

Generative shaping and material-forming (GSM) enables structure engineering of complex-shaped Li4SiO4 ceramics based on 3D printing of ceramic/polymer precursors

Impact of Sintering Aid Type and Content on the Mechanical Properties of Digital Light Processing 3D-Printed Si3N4 Ceramics

Additive manufacturing of flexible polymer-derived ceramic matrix composites