Abstract:Vat photopolymerization (VPP) 3D printing of ceramics normally uses ceramic slurries directly made of the target ceramic powder. It may become challenging when the ceramic powders are difficult-to-make and thus are expensive or rarely accessible. We have previously proposed a generative shaping and material-forming (GSM) 3D printing strategy, which involves the use of low-cost multi-component inorganic ceramic precursors as powder sources. The shaping of complex structures was realized through VPP, followed by reaction sintering to form the target ceramic material. In the current study, as a step further, ceramic (Li2CO3) and polymer (methyl polysiloxane) combined precursors were employed as an alternative material source for the first time to go through the 3D printing and reaction sintering processes, complementing the application range of the proposed GSM strategy. The slurry formulation and printability, the sinterability of the printed parts and the microstructures and mechanical performance of the sintered parts were characterized and optimized in accordance with the ingredient contents, particularly the stoichiometric ratios of Si:Li in the precursors. As a result, complex-structured Li4SiO4 ceramics with high purity were fabricated based on the use of Li2CO3 ceramic and Si-rich polymer as precursors. Through the advanced characterization and analysis of material phase and microstructural evolution, it was found that the fabricated complex-structured Li4SiO4 ceramics based on a precursor slurry with a solid content of 40 vol%, a Si:Li ratio of 1:2.5, and a sintering temperature of 850 °C showed a high phase purity of 97.23% and a compressive strength of 15.24 ± 0.33 MPa, with a skeleton’s relative density of 65.31% is achieved. The results showed greatly enhanced strength at much higher porosities, which might be advantageous and beneficial to structure engineering for mechanical enhancement and the improvement of tritium release effectiveness. Compared with the previous study using multi-component ceramic powder precursors, the ceramics prepared in this study exhibited enhanced microstructural stability and higher phase purity with an advantageously lower sintering temperature. Further analysis revealed that compared with the high temperature solid-state reaction of multi-component ceramic powder precursors, the involvement of the Si-rich polymer precursor enabled the more efficient and complete synthesis of Li4SiO4 as a result of the accelerated covering and cleavage of Si–O–Si bonds on the Li2CO3 particles at a much lower temperature. The present work suggests that the GSM strategy using combined ceramic and polymer precursors as proposed in this study is a promising alternative method to produce high quality Li4SiO4 components with complex structures.

Influence of the content of polymethyl methacrylate on the properties of porous Si3N4 ceramics fabricated by digital light processing

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Influence of the ratio of sintering aids on the properties of porous Si3N4 ceramics fabricated by digital light processing

Preparation and properties of porous silicon nitride ceramics with polymethyl methacrylate as pore-forming agent

Porous Si3N4 ceramics with hierarchical pore structures prepared by gelcasting using DMAA as gelling agent and PS as pore–forming agent

Preparation of porous Si 3 N 4 ceramics via tailoring solid loading of Si 3 N 4 slurry and Si 3 N 4 poly-hollow microsphere content

Preparation and properties of Si3N4 ceramics via digital light processing using Si3N4 powder coated with Al2O3-Y2O3 sintering additives

Microstructure and properties of porous Si 3 N 4 ceramics fabricated by digital light processing combined with spark plasma sintering

3D-printing of polymer‐derived SiCN ceramic matrix composites by digital light processing

Selective laser sintering of porous Al2O3-based ceramics using both Al2O3 and SiO2 poly-hollow microspheres as raw materials

High-strength and low-dielectric porous Si3N4 ceramics prepared by gelcasting using DMAA

Impact of Sintering Aid Type and Content on the Mechanical Properties of Digital Light Processing 3D-Printed Si3N4 Ceramics

In-situ Reaction Synthesis of Porous Si2N2O-Si3N4 Multiphase Ceramics with Low Dielectric Constant Via Silica Poly-Hollow Microspheres

Generative shaping and material-forming (GSM) enables structure engineering of complex-shaped Li4SiO4 ceramics based on 3D printing of ceramic/polymer precursors

Effect of TMAH as a modifier on the performance of Si3N4 stereolithography pastes

Increased microwave absorption property of porous Si3N4 ceramics by loading polymer-derived SiCN for a multifunctional design

Fabrication and properties of alumina ceramics shaped by digital light processing as an additive manufacturing technology

Mechanical and dielectric properties of porous Si3N4 ceramics prepared by modified water‐based gel casting

Optimizing the properties of vat photopolymerization 3D-printed SiC ceramics by multi-infiltration

Investigation of curing behavior and mechanical properties of SiC ceramics prepared by vat photopolymerization combined with pressureless liquid-phase sintering using Al 2 O 3 -coated SiC powder

Fabrication and properties of Si2N2O-Si3N4 ceramics via direct ink writing and low-temperature sintering