Abstract:Diesel hydrogenation unit is an important equipment for processing inferior oil in petroleum refining enterprises. Among them, the U-tube heat exchanger has been in high temperature and corrosive environment containing chlorine for a long time. Serious problem of tube bundle corrosion failure caused by ammonium chloride salt deposit. Anatomy of the diesel hydrogenation heat exchanger showed that the leakage part mainly appeared in the outermost bundle of the heat exchanger tube near the exit section, and the local area showed a large area of gully damage. Metallographic and XRD results show that the failure tube bundle material does not have manufacturing defects, and the corrosion location scale contains NH4Cl and iron oxides. The process flow analysis based on PR-NRTL model showed that the heat exchanger was in the NH4Cl crystallization temperature range, and the crystallization temperature increased with the increase of N and Cl contents in raw materials. Fluid simulation analysis of inlet tube box and single U-tube is carried out by using component transport equation and condensation model. Computational fluid dynamics (CFD) results indicate that there is a low velocity zone with high volume fraction of gas phase in the tube box. The higher gas volume fraction results in the formation of more NH4Cl particles into the U-tube bundle during heat transfer cooling. With the decrease of temperature, liquid water content in U-tube increases gradually and mainly distributes at both sides and bottom of tube bundle. The gas phase gradually fills the top of the tube bundle, and the oil and gas stratification becomes more obvious. The mass transfer rate and corrosion rate were the highest at the bottom and both sides of the tube bundle. With the temperature decreases, the NH4Cl particles generated in the tube continue to increase. The particles were deposited at 2000–3000 mm near the outlet section of the U-tube tube. NH4Cl particles absorbed liquid water, resulting in under-deposit corrosion of the tube bundle, and eventually led to the thinning and leakage of the heat exchanger tube bundle.

Crystallization Behavior of Ammonium Chloride in High-Pressure Heat Exchanger of Hydrotreating Unit

Analysis of Multiphase Flow and Heat and Mass Transfer for Ammonium Chloride Crystallization of the High-Pressure Heat Exchanger in Hydrogenation Unit

Failure analysis of ammonium chloride salt coagulation corrosion of U-tube heat exchanger in diesel hydrogenation unit

Experimental study on crystal deposition mechanism of ammonium chloride particles on the surface of heat exchange tube

Cause Analyses of the Weld Seam Cracks of a Prehydrogenating Reactor

Numerical Simulation on Hydrogen Induced Cracking Behavior of 4130X Hydrogen Storage Vessel with Defect

Analysis on the corrosion failure of U-tube heat exchanger in hydrogenation unit

Effect of NH 4 Cl fouling on heat transfer process of heat exchange tube under forced convection condition

Numerical investigation of corrosive gases absorption process by water injection in hydrogenation reaction effluent system

Mitigation of the ammonium salts corrosion in overhead condensing system of crude tower

Study on Dew Point Corrosion and Ammonium Salt Depositing at Low Temperature System of Atmospheric and Vacuum Distillation Unit

Effect of ammonium salt on corrosion of pipelines and components in a crude oil distillation column: Electrochemical and AIMD studies

Experimental Research on the Vapor Pressures of CaCl2–H2O and MgCl2–H2O As Working Fluids of Absorption Heat Transformers at High Temperature

Effect of Hydrogen on Corrosion Behavior of 321 Stainless Steel in NH4Cl Solution

CORROSION MECHANISM FOR HYDROGENATION SYSTEM EFFLUENT AIR COOLERS

Pressure Drop and Heat Transfer Characteristics of Tetra-N-butyl Ammonium Bromide Clathrate Hydrate Slurry During Flow Melting and Generating in a Double-Tube Heat Exchanger

Experimental Investigation of Flow and Heat Transfer Characteristics in the Generation of Clathrate Hydrate Slurry

Influence of crystal layer on the flow and heat transfer characteristics during TBAB CHS generation in a double-tube heat exchanger

Analysis of Cracking of Pressure Gauge Spring Tube for Hydrogenation Plant

Study on Design Calculation of the Wound-Tube Heat Exchanger in Hydrogen Recovery System

Effect of carbonized ammonia constituent on the crystallization process