Abstract:Both numerical simulation and hardness measurements were used to determine the mechanical and microstructural behavior of AZ31 bulk samples when submitted to the Equal Channel Angular Pressing (ECAP) technique. Billets of this representative of Mg-rich alloys were submitted to different numbers of passes for various ECAP modes (anisotropic A, isotropic BC). The strain distribution, the grain size refinement, and the micro-hardness were used as indicators to quantify the effectiveness of the different processing routes. Structural characterizations at different scales were achieved using Scanning Electron Microscopy (SEM), micro-analysis, metallography, Small Angle Neutron Scattering SANS, X-Ray Diffraction (XRD), and texture determination. The grain and crystallite size distribution and orientation as well as defect impacts were determined. Anelastic Spectroscopy (AS) on mechanically deformed samples have shown that the temperature of ECAP differentiate the fragile to ductile regime. MgH₂ consolidated powders were checked for using AS to detect potential hydrogen motions and interaction with host metal atoms. After further optimization, the different mechanically-treated samples were submitted to hydrogenation/dehydrogenation (H/D) cycles, which shows that, for a few passes, the BC mode is better than the A one, as supported by theoretical and experimental microstructure analyses. Accordingly, the hydrogen uptake and (H/D) reactions were correlated with the optimized microstructure peculiarities and interpreted in terms of Johnson-Avrami- Mehl-Kolmogorov (JAMK) and Jander models, successively.

The influence of ECAP on microstructure evolution of aluminium alloys during in-situ heating in TEM

The Effect of Heat Treatments on the Microstructural Evolution of Twin-Roll-Cast Al-Fe-Si Alloys

Influence of Texture on the Mechanical Properties of a Mg-6Al-1Zn-0.9Sn Alloy Processed by ECAP

High-Temperature Phase Transformations in Al-Li-Cu-Mg-Zr-Sc Alloy Studied via In Situ Electron Microscopy

Eff ects of Diff erent Mechanical Alloying Parameters on Microstructure of High Temperature Nanocrystalline Cu-Ta Alloys

MEMS-based in situ electron-microscopy investigation of rapid solidification and heat treatment on eutectic Al-Cu

Effect of Equal Channel Angular Extrusion on the Thermal Conductivity of an AX52 Magnesium Alloy

Effect of solution heat treatment on the internal architecture and compressive strength of an AlMg4.7Si8 alloy

Effects of High Temperature ECAE Process on Microstructures and Martensitic Transformation of TiNi Shape Memory Alloy

Microstructure, Phase Transformation and Wear Behavior of Cu–10%Al–4%Fe Alloy Processed by ECAE

Effect of Extrusion Temperature on Microstructure Evolution and Strengthening Mechanism of 7003-T6 Aluminum Alloy by Equal Channel Angular Pressing

Unleashing the microstructural evolutions during hot deformation of as-cast AlCoCrFeNi 2.1 eutectic high entropy alloy

Effect of the Equal Channel Angular Pressing on the Microstructure and Phase Composition of a 7xxx Series Al-Zn-Mg-Zr Alloy

Microstructure and dislocation density evolutions in MgAlZn alloy processed by severe plastic deformation

Experimental and Numerical Investigation of the ECAP Processed Copper: Microstructural Evolution, Crystallographic Texture and Hardness Homogeneity

Shear Deformation and Texture Evolution in Al Alloys Processed for One Pass by ECAP

Microstructure Evolution of Processed Mg-Al-Zn Alloy by Equal Channel Angular Extrusion in Semi-Solid Isothermal Treatment

Microstructural Evolution of AZ61 Magnesium Alloy Predeformed by ECAE During Semisolid Isothermal Treatment

Effect of ECAP on microstructure uniformity and mechanical properties of high purity aluminum

The microstructure and mechanical properties of Mg-Sn-based alloy processed by differential-thermal equal channel angular pressing

Microstructure Optimization of Mg-Alloys by the ECAP Process Including Numerical Simulation, SPD Treatments, Characterization, and Hydrogen Sorption Properties