Abstract:Microstructure formation of a hypo-eutectic Al-11Cu (atom percent) alloy during solidification after laser melting has been studied by transmission electron microscopy (TEM). The evolution of the solid-liquid-interface velocity, VSL, during the solidification process has been determined from direct observation by in-situ TEM. This enabled correlating VSL with development of four distinct microstructure zones. Crystal growth mode transitions from planar to cellular, cellular to dendritic, dendritic to cellular, and cellular to planar, have been observed for the accelerating solid-liquid-interface. The transition from coupled two-phase growth to the single-phase growth occurred for VSL = Va = (0.80±0.05) m/s, where Va is the velocity of absolute stability, at the onset of banded morphology grain formation. The in-situ and post-mortem TEM uniquely permitted determination of the non-equilibrium solidus for the rapidly solidifying Al-11Cu alloy. Experimental evidence for solute clustering and chemical ordering tendencies at length scales on the order of ≤ 5nm has been detected in the single-phase regions of the banded grains. The structural features of the single-phase bands have been interpreted as signatures of 'frozen in' configurations present in the liquid boundary layer adjacent to the growing crystal, which has a width of about 3nm. The nano-scale spatiotemporal resolution experimental TEM studies performed here provided quantitative metrics, e.g. the solidification interface velocity dependent solute concentration of the α-Al phase and the near-atomic scale structure in the single-phase bands, that are uniquely suitable for comparison with theory and model predictions for solidification microstructure development in multicomponent alloys after laser melting.

MEMS-based in situ electron-microscopy investigation of rapid solidification and heat treatment on eutectic Al-Cu

Interface velocity dependent solute trapping and phase selection during rapid solidification of laser melted hypo-eutectic Al-11at.%Cu alloy

In situ electron microscopy studies of electromechanical behavior in metals at the nanoscale using a novel microdevice-based system

High temperature in situ SEM assessment followed by ex situ AFM and EBSD investigation of the nucleation and early growth stages of Fe-Al intermetallics

Effect of solution heat treatment on the internal architecture and compressive strength of an AlMg4.7Si8 alloy

In-situ observations of solidification process of Fe–Al–Ta eutectic alloy

The influence of ECAP on microstructure evolution of aluminium alloys during in-situ heating in TEM

Sub-micrometre holotomographic characterisation of the effects of solution heat treatment on an AlMg7.3Si3.5 alloy

Thermoelastic martensitic transition and shape memory effect in Ti2NiCu alloy at micro- and nanoscale

Microstructure evolution during directional solidification of off-eutectic Al-Cu-Mg alloys

In Situ Observation of Liquid Solder Alloys and Solid Substrate Reactions Using High-Voltage Transmission Electron Microscopy

Isothermal Solidification of Micro Layers of Molten Aluminum Alloys

Advanced preparation of plan-view specimens on a MEMS chip for in situ TEM heating experiments

High-Temperature Phase Transformations in Al-Li-Cu-Mg-Zr-Sc Alloy Studied via In Situ Electron Microscopy

Measuring coefficient of thermal expansion of materials of micrometre size using SEM/FIB microscope with in situ MEMS heating stage

High-speed synchrotron X-ray imaging of melt pool dynamics during ultrasonic melt processing of Al6061

Phase Separation and Anomalous Volume Expansion in Frozen Microscale Eutectic Indium-Gallium upon Remelting

Achieving strength-ductility synergy in Al-4.5 wt%Cu binary alloy through semisolid isothermal treatment coupled with ECAP

Ultrasound Cavitation Induced Nucleation in Metal Solidification: an Analytical Model and Validation by Real-Time Experiments.

Development of a novel in-situ measurement method for thermo-mechanically coupled material characterization of high-strength aluminum alloys

Cellular Automaton Simulation and Experimental Validation of Eutectic Transformation During Solidification of Al-Si Alloys