Abstract:The research presented in this paper aspired to understand how the simultaneous addition of Ge and Sn in an Hf-free Nb-silicide-based alloy affected its oxidation resistance. Results are presented for the Nb-24Ti-18Si-5Al-5Cr-5Ge-5Sn alloy (at.%) which was studied in the as-cast and heat-treated (1400 °C/100 h) conditions and after isothermal oxidation in air at 800 and 1200 °C. There was macrosegregation in the cast alloy, in which the Nbss formed at a low volume fraction and was not stable after heat treatment at 1400 °C. The βNb5Si3, A15-Nb3Sn, and C14-NbCr2 were stable phases. The alloy did not undergo pest oxidation at 800 °C, and there was no spallation of its scale at 1200 °C. There was enrichment in Ge and Sn in the substrate below the scale/substrate interface, where the compounds Nb3Sn, Nb5Sn2Si, (Ti,Nb)6Sn5, and Nb5Ge3 were formed. After the oxidation at 1200 °C, the solid solution in the bulk of the alloy was very Ti-rich (Ti,Nb)ss. Improvement of oxidation resistance at both temperatures was accompanied by a decrease and increase, respectively, of the alloy parameters VEC (valence electron concentration) and , in agreement with the alloy design methodology NICE (Niobium Intermetallic Composite Elaboration). The elimination of scale spallation at 1200 °C was attributed (a) to the formation of Ti-rich (Ti,Nb)ss solid solution and (Ti,Nb)6Sn5, respectively, in the bulk and below the scale, (b) to the low concentration of Cr in the scale, (c) to the absence of GeO2 in the scale, (d) to the formation of αAl2O3 in the scale, and (e) to the presence (i) of Nb5Ge3 below the scale/substrate interface and (ii) of oxides in the scale, namely, SiO2, Al2O3, TiO2, and SnO2, and Ti2Nb10O29,TiNb2O7, and AlNbO4, respectively, with a range of intrinsic thermal shock resistances and coefficient of thermal expansion (CTE) values that reduced stresses in the scale and the substrate below it.

Synthesis and Characterization of Silicide Coating on Niobium Alloy Produced Using Molten Salt Method

Microstructure and Cyclic Oxidation Behavior of Silicide Coatings Prepared by Molten Salt on Nb–Based Alloys

Formation and properties of niobium silicide coatings on Nb-Ta alloy substrate

Formation and oxidation behavior of refractory high-entropy silicide (NbMoTaW)Si2 coating

Formation and Oxidation Resistance of NbSi<sub>2</sub> Coatings on Niobium by Pack Cementation

Development and oxidation behavior of high entropy silicide (NbMoTaWV)Si2 coatings on NbMoTaWV alloy

Structure of Al-modified Silicide Coating on an Nb-silicide-based Ultrahigh Temperature Alloy Prepared by Pack Cementation Technique

High Temperature Oxidation Behavior at 1250°C: A New Multilayer Modified Silicide Coating Design Strategy on Niobium Alloys

Study on the Oxidation Behavior of TiB2-CeO2-Modified (Nb,Mo,Cr,W)Si2 Coating on the Surface of Niobium Alloy

Investigation on Preparation of Nb-Ti-Si-B Alloy Coatings with Siliconizing and Oxidation Resistance

Niobium alloy electron beam surface cladding silicide coating crack control

Design and preparation of MoSi2/SiO2-Nb2O5/NbSi2 multilayer coating on Nb alloy: Microstructure and hot corrosion behavior

The Protection, Challenge, and Prospect of Anti-Oxidation Coating on the Surface of Niobium Alloy

Formation and oxidation behavior of Ce-modified MoSi2-NbSi2 coating on niobium alloy

On the Microstructure and Isothermal Oxidation at 800 and 1200 °C of the Nb-24Ti-18Si-5Al-5Cr-5Ge-5Sn (at.%) Silicide-Based Alloy

Morphology of sintered silicide coatings remelted by high frequency electron beam

On the Microstructure and Properties of the Nb-23Ti-5Si-5Al-5Hf-5V-2Cr-2Sn (at.%) Silicide-Based Alloy—RM(Nb)IC

Study of morphological, physical and mechanical properties of thin NbN films synthesized via DC magnetron sputtering system

Hot Corrosion Behavior of NbSi2/SiO2-Nb2O5 Multilayer Coating on Nb Alloy

Synthesis of complex concentrated silicide coatings via reactive melt-infiltration: Exploring interfacial phenomena between Si-B melt and MoNbTaW high-entropy alloy

Microstructural Characterization and Anti‐Oxidation Properties of Molybdenum Disilicide Coating on Niobium by Spent MoSi 2 ‐Based Materials