Abstract:Abstract Heavy oil reservoirs remain challenging for surfactant-based EOR. In particular, selecting fine-tuned and cost effective chemical formulations requires extensive laboratory work and a solid methodology. This paper reports a laboratory feasibility study, aiming at designing a surfactant-polymer pilot for a heavy oil field with an oil viscosity of ~500cP in the South of Sultanate of Oman, where polymer flooding has already been successfully trialed. A major driver was to design a simple chemical EOR method, to minimize the risk of operational issues (e.g. scaling) and ensure smooth logistics on the field. To that end, a dedicated alkaline-free and solvent-free surfactant polymer (SP) formulation has been designed, with its sole three components, polymer, surfactant and co-surfactant, being readily available industrial chemicals. This part of the work has been reported in a previous paper. A comprehensive set of oil recovery coreflood tests has then been carried out with two objectives: validate the intrinsic performances of the SP formulation in terms of residual oil mobilization and establish an optimal injection strategy to maximize oil recovery with minimal surfactant dosage. The 10 coreflood tests performed involved: Bentheimer sandstone, for baseline assessments on large plugs with minimized experimental uncertainties; homogeneous artificial sand and clays granular packs built to have representative mineralogical composition, for tuning of the injection parameters; native reservoir rock plugs, unstacked in order to avoid any bias, to validate the injection strategy in fully representative conditions. All surfactant injections were performed after long polymer injections, to mimic the operational conditions in the field. Under injection of "infinite" slugs of the SP formulation, all tests have led to tertiary recoveries of more than 88% of the remaining oil after waterflood with final oil saturations of less than 5%. When short slugs of SP formulation were injected, tertiary recoveries were larger than 70% ROIP with final oil saturations less than 10%. The final optimized test on a reservoir rock plug, which was selected after an extensive review of the petrophysical and mineralogical properties of the available reservoir cores, led to a tertiary recovery of 90% ROIP with a final oil saturation of 2%, after injection of 0.35 PV of SP formulation at 6 g/L total surfactant concentration, with surfactant losses of 0.14 mg-surfactant/g(rock). Further optimization will allow accelerating oil bank arrival and reducing the large PV of chase polymer needed to mobilize the liberated oil. An additional part of the work consisted in generating the parameters needed for reservoir scale simulation. This required dedicated laboratory assays and history matching simulations of which the results are presented and discussed. These outcomes validate, at lab scale, the feasibility of a surfactant polymer process for the heavy oil field investigated. As there has been no published field test of SP injection in heavy oil, this work may also open the way to a new range of field applications.

Conversion of Acidic Heavy Resid to Surfactant for Separating Water-Oil Emulsions and Increasing Oil Production

Laboratory Evaluation of the Use of Solvent Extraction for Separation of Hydrophobic Organic Contaminants from Surfactant Solutions During Surfactant-Enhanced Aquifer Remediation

Developing New Recyclable and pH-Sensitive Amphiphile for Heavy Oil Emulsion and Demulsification: A Molecular Dynamics Study

A Surfactant for Enhanced Heavy Oil Recovery in Carbonate Reservoirs in High-Salinity and High-Temperature Conditions

Chemical Demulsification of Oil-in-Water Emulsion from Gas Condensate Field

Application of surfactants for the resolution of emulsions and suspensions in slop oil storage tanks, cleaning, and final disposal

Synergistic Collaboration between a Viscosity Reducer and a Surfactant for in Situ Emulsion Formation to Enhance Heavy-Oil Recovery

Research of emulsion properties of oil with selection of effective chemical reagents for destruction of arising emulsions

Experimental investigation of new derived anionic natural surfactant from peanut oil: Application for enhanced oil recovery

Surfactant-enhanced Removal of Hydrophobic Oils from Source Zones

Methods of separation of stable oil-water emulsions into phases and their application at production sites

Technology for producing anticorrosive materials from fat-containing waste

Novel green surfactant made from L-aspartic acid as enhancer of oil production from sandstone reservoirs: Wettability, IFT, microfluidic, and core flooding assessments

Application of Alkali-Novel Green Extracted Surfactant (AS) for Sustainable Chemical Enhanced Oil Recovery (CEOR) in Carbonate Petroleum Reservoirs

Emulsification and interfacial characteristics of different surfactants enhances heavy oil recovery: experimental evaluation and molecular dynamics simulation study

A Novel Hydroxylpropyl Sulfobetaine Surfactant for High Temperature and High Salinity Reservoirs

Application of a new anionic surfactant based on sesame oil by Alkali-Surfactant (AS) injection in chemical enhanced oil Recovery: Characterization, mechanisms and performance

One-Step Synthesis of New Amphiphilic Nonionic Surfactants Based on Alkylamine and Poly(ethylene glycol) Dimethacrylate for Demulsification of Arabian Heavy Crude Oil Emulsions

A New Logistically Simple Solution for Implementing Alkali-Surfactant-Polymer/Alkali-Cosolvent-Polymer in Difficult Environments: Evaluation of Concept with High Total Acid Number Viscous Crude Oil

Novel Nonylphenol Polyethoxylated Based Surfactants for Enhanced Oil Recovery for High-Mineralization Carbonate Reservoir

Experimental Design and Evaluation of Surfactant Polymer for a Heavy Oil Field in South of Sultanate of Oman