Abstract:Rigid polyurethane foams (RPUFs) were successfully modified with different weight ratios (0.5 wt%, 1 wt%, 2 wt%) of nanosilica and nanosilica suspension (nanosilica-enhanced with ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate, [bmim][PF6]). The resulting foams were evaluated by their processing parameters, chemical structure (Fourier Transform Infrared Spectroscopy Analysis, FTIR), morphology (Scanning Electron Microscopy Analysis, SEM), mechanical properties (compressive test, three-point bending test), viscoelastic behavior (Dynamic Mechanical Analysis, DMA), thermal property (Thermogravimetric Analysis, TGA, thermal conductivity) and application properties (water absorption, dimensional stability). The results showed that the morphology of modified foams is significantly affected by the type of the filler and filler content, which resulted in inhomogeneous, irregular, large cell shapes and further affected the physical and mechanical properties of resulting materials. RPUFs modified with nanosilica suspension represent better mechanical and thermal properties comparing to the RPUFs modified with pure nanosilica. The results showed that the best results were obtained for RPUFs modified with 1 wt% of nanosilica suspension. In comparison with unfilled foam, compositions modified with 1 wt% of nanosilica suspension provide higher density (44 kg/m3), greater compression strength (258 kPa measured parallel and 162 kPa measured perpendicular), and lower thermal conductivity (0.026 W/m·K). The results obtained in this study suggest that the introduction of nanosilica and nanosilica suspension over a certain optimal level (such as 2 wt%) has a negative effect on the cell morphology, which leads to deterioration of physico-mechanical properties of the modified foams.

Organic–inorganic nanocomposite films made from polyurethane dispersions and colloidal silica particles

PREPARATION AND STUDY ON STRUCTURE OF THE POLYIMIDE/SILICA HYBRID AND NANOCOMPOSITE FILMS

Preparation and Dielectric Properties of Polyimide/silica Nanocomposite Films Prepared from Sol–gel and Blending Process

Synthesis and Properties of Nanosilica‐reinforced Polyurethane for Grouting

The synthesis and properties of siloxane-urethane copolymers aqueous nanodispersion using hydroxyalkyl and hydrohxypolyester terminated polydimethylsiloxane

Structure and Properties of Polyurethane/nanosilica Composites

Interaction and Microstructure of Polyurethane/Silica Hybrid Films Prepared by Sol-Gel Process

Film‐forming Behavior and Mechanical Properties of Colloidal Silica/polymer Latex Blends with High Silica Load

Composites of rigid polyurethane foams and silica powder filler enhanced with ionic liquid

The Core-Shell Structured Aqueous Dispersions of the Siloxane-Grafted Polyurethane Copolymers with High Transparency

Poly(methylmethacrylate)-silica nanocomposites films from surface-functionalized silica nanoparticles

Preparation of an Ultraviolet‐curable Water‐borne Poly(urethane Acrylate)/silica Dispersion and Properties of Its Hybrid Film

Synthesis and Characterization of Novel Organosilicon‐modified Polyurethane

Microstructure and Properties of Organosoluble Polyimide/silica Hybrid Films

Effect of Nanosilica on the Properties of Polyester‐based Polyurethane

Preparation of Inorganic Nanoparticles/Polyimide Hybrid Film by Sol Gel Method

Properties of in-situ polymerized casting polyurethane/nano-silica composites

Mesoporous Silica-Reinforced Polymer Nanocomposites

Preparation and characterization of nanocomposite polyurethane.

Synthesis and Characterization of Polyimide/Silica Nanocomposite Films

In Situ Polymerization and Characterization of Polyester‐based Polyurethane/nano‐silica Composites