Abstract:Proton Exchange Membrane Fuel Cells (PEMFCs) are promising for heavy-duty vehicles (HDV) in the strive to make the transportation sector more sustainable. However, because of the small temperature gradient between the cell (typically run around 80°C) and the ambient temperature, these cells require a large cooling system. Raising the operating temperature to an intermediate temperature range (IT: 80 – 120 °C) would reduce the cooling system size required in HDVs and improve the tolerance towards contaminants, although higher temperature may accelerate degradation [1,2]. To be able to withstand IT operation, reinforcements and chemical modifications have been implemented in commercial PFSA polymers. Unfortunately, most of the data available for PEMFCs are referred to non-reinforced membranes and only few studies analysed the latter under realistic operating conditions. Among some possible issues regarding proton exchange membranes (PEMs), hydrogen crossover is an undesirable, but inevitable phenomenon. The membrane is not perfectly impermeable to hydrogen gas and this results in a safety concern, lower cell efficiency and can lead to faster cell degradation. This work investigates the influence of the reinforcement in a PEM on the hydrogen crossover. Specifically, Nafion HP (reinforced) and Nafion 211 (non-reinforced) are compared under different operating conditions. The purpose of the reinforcement is to improve thermo-mechanical stability, and its physical properties can differ from the rest of the membrane, which can influence hydrogen crossover. Using electrochemical methods, the hydrogen crossover is measured in-situ in a PEMFC with hydrogen on one side and inert gas on the other side. The measurements have been performed between 80 and 120 °C, at different cell relative humidity (RH) conditions (20-90 %) and multiple levels of pressure for both reinforced and non-reinforced membranes. Particular attention has been paid to the case in which the hydrogen side of the cell is more pressurized than the inert side, as this is most often the case in HDV applications. In such conditions, hydrogen permeation increases considerably as a result of the total pressure gradient over the membrane, although this factor is rarely considered in the literature [3]. By adapting the methodology established in our previous work [4], here the effects of the differential total pressure and hydrogen partial pressures are decoupled through a systematic dilution of the hydrogen gas stream. Special points are measured in which the hydrogen partial pressure is kept equal to the ambient case, while the total pressure on the hydrogen side is increased by adding the inert gas, as shown in Figure 1, plot I. Results show that the presence of a reinforcement affects the amount of hydrogen that crosses through the membrane, as seen in Figure 1. Moreover, among the different conditions tested, higher total pressures, especially on the hydrogen side of the cell, are affecting hydrogen crossover the most, while a more modest change is observed for different RH and cell temperatures. The observation that pressure is the most important factor for hydrogen crossover has noteworthy implications and should have an influence when deciding at which pressure the PEMFC is operated in transportation applications. Minimizing hydrogen crossover, while still ensuring adequate cell performance, should be a priority to improve the overall fuel consumption and the electric power obtained from the fuel cell. Figure 1: Hydrogen crossover due to concentration gradients and, in certain conditions, to a differential total pressure. Three different conditions are used to measure crossover, whose results are reported in the right figure: I) the total pressure on the hydrogen side is increased by diluting with inert gas, while the hydrogen partial pressure is kept constant, the inert side is unvaried; II) the total pressure is increased symmetrically on both sides, the hydrogen side is not diluted; III) the total pressure on the hydrogen side is increased and no dilution is employed. [1] Cullen et al., “New roads and challenges for fuel cells in heavy-duty transportation,” Nat. Energy, 2021, doi:10.1038/s41560-021-00775-z. [2] Akitomo et al., “Investigation of effects of high temperature and pressure on a polymer electrolyte fuel cell with polarization analysis and X-ray imaging of liquid water,” J. Power Sources, 2019, doi:10.1016/j.jpowsour.2019.04.115. [3] Kreitmeier et al., “Investigation of membrane degradation in polymer electrolyte fuel cells using local gas permeation analysis,” J. Power Sources, 2012, doi:10.1016/j.jpowsour.2012.03.071. [4] Butori et al., “The Effect of Oxygen Partial Pressure and Humidification in Proton Exchange Membrane Fuel Cells at Intermediate Temperature,” J. Power Sources, 2023, doi:10.1016/j.jpowsour.2023.232803. Figure 1

Experimental Investigation of Air Relative Humidity (RH) Cycling Tests on MEA/Cell Aging in PEMFC Part II: Study of Low RH Cycling Test with Air RH at 62%/0%

Study of Relative Humidity on Durability of the Reversal Tolerant Proton Exchange Membrane Fuel Cell Anode Using a Segmented Cell

Identification of Dominant Transport Mechanisms in PEMFC Cathode Catalyst Layers Operated under Low RH

Effect of Catalyst Layer Ionomer Content on Performance of Intermediate Temperature Proton Exchange Membrane Fuel Cells (It-Pemfcs) under Reduced Humidity Conditions

Membrane Electrode Assembly with Pt/SiO2/C Anode Catalyst for Proton Exchange Membrane Fuel Cell Operation under Low Humidity Conditions

Ultrahigh PEMFC performance of a thin-film, dual-electrode assembly with tailored electrode morphology

Effect of Ionomer Content and Relative Humidity on IT-PEMFC Performances at 120 Oc

Pore-scale Study of Effects of Relative Humidity on Reactive Transport Processes in Catalyst Layers in PEMFC

Electrochemical Impedance Analysis with Transmission Line Model for Accelerated Carbon Corrosion in Polymer Electrolyte Membrane Fuel Cells

Uncoupling Characteristics Of Temperature And Relative Humidity Distribution In A Commercial-Size Polymer Electrolyte Membrane Fuel Cell

Investigation of Catalyst Degradation in Proton Exchange Membrane Fuel Cell By Identical Location Electron Microscopy

Multiple in-situ measurement of water transport in the bipolar plate of proton exchange membrane fuel cell

An EIS approach to quantify the effects of inlet air relative humidity on the performance of proton exchange membrane fuel cells: A pathway to developing a novel fault diagnostic method

Diagnosis of Membrane Electrode Assembly Degradation with Drive Cycle Test Technique

Catalyst Microstructure Examination of PEMFC Membrane Electrode Assemblies vs. Time

High protonic resistance of hydrocarbon-based cathodes in PEM fuel cells under low humidity conditions: Origin, implication, and mitigation

Ionic conductivity and hydrogen crossover for IT-PEMFCs: Influence of pressure, temperature, relative humidity and reinforcement

Evaluation of thermal cycling on durability and PA loss in high temperature PEM fuel cells

Post mortem Study of Catalyst Degradations Occurring in High-Temperature Proton Exchange Membrane Fuel Cells Upon Start-Stop Operation

Microstructural Changes of Membrane Electrode Assemblies During Pefc Durability Testing at High Humidity Conditions

Evaluation of Hydrogen Crossover in Pemfcs at Intermediate Temperature (80 - 120 °C)