Abstract:NiO nanomaterials prepared using a solid–liquid NH3·H2O precipitation method (NiO-NSL) were tested in the catalytic combustion of methane. The NiO-NSL presented a characteristic rod-like nanostructure with a length of about a few hundred nanometers except for a part of the nanoparticles. For comparison, the NiO nanomaterials prepared by the traditional liquid-phase NH3·H2O precipitation method (NiO-NLL) were tested in the same reaction conditions. NiO-NSL exhibited significantly higher methane combustion activity than NiO-NLL and achieved the complete combustion of methane at 390 °C, which was outstanding in non-noble metal-based catalyst. X-ray photoelectron spectroscopy (XPS) and hydrogen-temperature-programmed reduction (H2-TPR) results indicate that the surface Ni2+ content of NiO-NSL was higher than that of NiO-NLL, and the presence of more Ni2+ might be responsible for the enhanced activity. DFT calculations prove that the energy barrier for C–H bond activation on Ni2+ was lower than that on Ni3+, which was consistent with the higher methane catalytic combustion activity of NiO-NSL. In addition, when the precipitating agent was replaced with NaOH and (NH4)2CO3, the generalization of the solid–liquid precipitation method in the preparation of the NiO catalysts was also tested. The results show that the solid–liquid precipitation method proposed in this work was still applicable when NaOH was used as a precipitant. However, with the use of (NH4)2CO3 as a precipitant, the methane catalytic activity of the NiO nanoparticles prepared by the solid–liquid precipitation method was reduced to a certain extent compared with the traditional liquid-phase precipitation method. This research can open up a highly efficient and environmentally friendly method for the synthesis of methane combustion catalysts.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsanm.1c00732?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsanm.1c00732</a>.Stability test results of NiO-NSL (Figure S1); wide-angle XRD patterns of the as-precipitated samples using (NH4)2CO3 as the precipitant and a standard xNiCO3·yNi(OH)2 sample (Figure S2); representative TEM images of the precursors and as-calcined catalysts of the other four samples (Figures S3 and S4); specific performance data of samples in previous research (Table S1); XPS analysis of the other samples (Table S2, Figures S5 and S6); H2-TPR profiles of the other samples (Table S3, Figures S7 and S8); detailed DFT calculation results (Table S4); the surface model used in the calculations (Figure S9) (<a class="ext-link" href="/doi/suppl/10.1021/acsanm.1c00732/suppl_file/an1c00732_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Total Oxidation of Methane over the LaNi1−xMxO3 (M: Mn, Ag, Cu, Co) Perovskites

Preparation and evaluation of the LaCu1-xNixO3 (x = 0, 0.1, 0.3, 0.5 and 0.7) perovskite catalysts for total oxidation of methane

Highly Effective La-deficient La Ce MnO3 Mixed Oxides for the Complete Oxidation of Methane

Catalytic combustion of methane over various perovskite-type oxides

Effects of partial substitution of Cu by Mn and Co in LaCu0.5Ni0.5O3 catalyst synthesized by mechanochemical method in the total oxidation of methane

Catalytic CO2 Reforming of Methane over Perovskite Noble Metals

Methane Catalytic Combustion under Lean Conditions over Pristine and Ir-Loaded La1−xSrxMnO3 Perovskites: Efficiency, Hysteresis, and Time-on-Stream and Thermal Aging Stabilities

Methane reforming to syngas over LaNi x Fe 1−x O 3 (0≤ x ≤1) mixed-oxide perovskites in the presence of CO 2 and O 2

Activation of Methane over Perovskite Catalysts

Nickel Oxide As an Effective Catalyst for Catalytic Combustion of Methane

Enhancement of the redox reactions of the La0.8Sr0.2MnO3 catalyst by surface acid etching: A simple synthesis strategy to high-performance catalysts for methane combustion

Oxygen desorption and oxidation-reduction kinetics with methane and carbon monoxide over perovskite type metal oxide catalysts

Partial Oxidation of Methane Over NiOx/Hierachichal ZSM-5 Catalyst

Pseudo core-shell LaCoO3@MgO perovskite oxides for high performance methane catalytic oxidation

The Ni Catalyst Supported on the FSP-made Transition Metal (Co, Mn, Cu or Zn) Doped La2O3 Material for the Dry Reforming of Methane

Investigation of catalytic methane oxidation over Ag/Co2MOx (M = Co, Ni, Cu) catalysts with varying interfacial electron transfer

Irregularly Shaped NiO Nanostructures for Catalytic Lean Methane Combustion

Performance of Modified La Xsr1- Xmno3 Perovskite Catalysts for NH3 Oxidation: TPD, DFT, and Kinetic Studies.

Investigation on the Catalytic Combustion of CO over LaMn 1‐ X Cu X O 3 Promoted by Acid Treatment

Evaluation of Three‐Dimensionally Ordered Macroporous LaFe &Lt;sub>1-X</sub>co <sub>x</sub>o <sub>3</sub> Perovskites and Their Performance for Catalytic Oxidation of Methane

Promoted Ni Catalyst Over Titania-Zirconia Support for Partial Oxidation of Methane: Simple and Practical Catalysts