Abstract:Superplastic behavior of ultrafine-grained (UFG) Al-6Mg-0.12Sc-0.10Zr-0.1X alloys, where X = Yb (Alloy #1-Yb), Er (Alloy #2-Er), and Hf (Alloy #3-Hf), has been studied. The total content of Sc, Zr, Yb, Er, Hf in the alloys was 0.32 wt.% (0.117-0.118 at.%). The alloys used for benchmarking were Al-6Mg-0.12Sc-0.20Zr (Alloy #4-Zr) and Al-6Mg-0.22Sc-0.10Zr (Alloy #5-Sc). Their UFG microstructure was formed with ECAP. Two different types of deformation behavior during superplasticity were demonstrated. A simultaneous increase in yield stress and elongation to failure during superplastic deformation was discovered. High deformation temperatures were shown to cause a competition between dynamic (strain-induced) grain growth and dynamic recrystallization, leading to a finer grain microstructure. The values of strain hardening factor (n), strain rate sensitivity factor (m), and superplastic deformation threshold stress (Sp) were determined. The impact of the type and concentration of alloying elements on the deformation behavior and dynamic grain growth of Al-6%Mg alloys was investigated. It was established that the maximum elongation to failure in Alloy #1-Yb and Alloy #2-Er is observed at lower deformation temperatures than in Alloy #4-Zr and Alloy #5-Sc. The superplastic properties of Alloy #3-Hf are superior to those of Alloy #4-Zr and Alloy #5-Sc with high content of alloying elements (in at.%). Alloy #1-Yb manifests good elongation to failure (910%) at low temperatures (400 oC). The satisfiability of Hart's criterion for calculating uniform deformation value under superplastic conditions was verified. It was demonstrated that cavitation when pores are formed in large Al3X particles at high temperatures causes early failure of aluminum alloys.

Aluminum alloys with enhanced strength for superplastic forming

On Mechanical Properties and Superplasticity of Mg–15Al–1Zn Alloys Processed by Reciprocating Extrusion

High Strain Rate Superplasticity in Al-Zn-Mg-Based Alloy: Microstructural Design, Deformation Behavior, and Modeling

An Mg‐Al‐Zn Alloy with Verry High Specific Strength and Superior High‐strain‐rate Superplasticity Processed by Reciprocating Extrusion

Microstructure Evolution, Constitutive Modelling, and Superplastic Forming of Experimental 6XXX-Type Alloys Processed with Different Thermomechanical Treatments

A High-Strength Extruded Mg-Gd-Zn-Zr Alloy with Superplasticity

Superplasticity of 5083 Alloys with Zr and Mn Additions Produced by Reciprocating Extrusion

Formation of high strength Mg–Cu–Zn–Y alloys

Study of forming process of structure of high-strength aluminum alloys based on Al—Zn—Mg—Cu and Al—Zn—Mg—Fe—Ni systems to achieve improved mechanical properties

Superplastic Deformation of a Heat-Resistant Al–Cu–Mg–Ag–Mn Alloy

Investigation of Microstructures and Mechanical Properties of Ultra-High Strength Al-Zn-Mg-Cu Alloy Prepared by Rapid Solidification and Hot Extrusion

Superior mechanical properties of a selective-laser-melted AlZnMgCuScZr alloy enabled by a tunable hierarchical microstructure and dual-nanoprecipitation

Ultra-high strength Al-Zn-Mg-Cu alloys with high zinc content prepared via powder hot extrusion

Approaching 1 GPa ultra‐high tensile strength in a nanostructured Al‐Zn‐Mg‐Cu‐Zr‐Sc alloy prepared by severe plastic deformation

Microstructure Thermal Stability and Superplastic Behavior of Al-6%Mg-0.12%Sc-0.10%Zr-0.10%(Yb, Er, Hf) Ultrafine-Grained Alloys

The Study on Heat Treatment Microstructure and Properties of Extruded Al-Mg-Si-Mn-Cr-Zr Alloy

A novel die-casting Mg alloy with superior performance: Study of microstructure and mechanical behavior

Microstructures and Mechanical Properties of Hot-extruded Mg-6Zn-xCu-0.6Zr(x=0,0.5,1.0,1.5) Alloys

Microstructure and properties of a novel ultra-high strength, high elasticity and high plasticity Cu–20Ni–20Mn-0.3Nb-0.3Cr-0.1Zr alloy

Superplastic Behavior and Microstructural Evolution in a Commercial Mg-3Al-1Zn Magnesium Alloy.

Super High Strength Aluminum Alloy Processed By Mechanical Alloying And Hot Extrusion