Abstract:The limitation of the currently available thermal management method has put an ever serious challenge for computer chip designers. A liquid metal with low melting point around room temperature was recently identified as a powerful coolant of driving heat away because of its superior thermo-physical properties and the unique ability to be driven efficiently by a completely silent electromagnetic pump. However, the adoption of gallium, one of the best candidates as metal coolant so far, may cause serious corrosion to the structure materials and subsequently affect the performance or even dangerous running of the cooling system. To address this emerging critical issue, here the compatibility of gallium with four typical metal substrates (6063 Aluminum-Alloy, T2 Copper-Alloy, Anodic Coloring 6063 Aluminum-Alloy and 1Cr18Ni9 Stainless Steel) was comprehensively investigated in order to better understand the corrosion mechanisms and help find out the most suitable structure material for making a liquid metal cooling device. To grasp in detail the dynamic corrosion behavior, an image acquisition and contrasting method was developed. Moreover, corrosion morphology analyses were performed by means of scanning electron microscope (SEM). The chemical compositions of the corroded layers were evaluated using energy dispersive spectrometry (EDS). According to the experiments, it was found that, the corrosion of the 6063 Aluminum-Alloy was rather evident and serious under the temperature range for chip cooling. The loose corrosion product will not only have no protection for the inner substrate, but also accelerate the corrosion process. Compared to the 6063 Aluminum-Alloy, T2 Copper-Alloy showed a slow and general corrosion, but part of the corrosion product can shed from the substrate, which will accelerate corrosion action and may block the flowing channel. Anodic Coloring 6063 Aluminum-Alloy and 1Cr18Ni9 Stainless Steel were found to have excellent corrosion resistance among these four specimens. No evident corrosion phenomena were found under the examination of SEM and EDS when exposed for 30 days at the temperature of 60°C, which suggests their suitability as structure materials for the flow of liquid metal. However, as for the Anodic Coloring 6063 Aluminum-Alloy, surface treatment and protection are of vital importance. The present study is of significance for making a liquid metal chip cooling device which can actually be used in the future computer industry.

Inhibition of Corrosion of the Hypereutectic Aluminum-Silicon Alloys in Antifreeze Solutions

Anticorrosion properties of antifreeze of internal combustion engine cooling system

A review on corrosion and corrosion inhibition behaviors of magnesium alloy in ethylene glycol aqueous solution

Corrosion Inhibition of Aluminum Alloy in 50% Ethylene Glycol Solution

Corrosion Behaviour of Mild Steel in Chloride Solutions with Na2HPO4 Additive and the Development of Antifreeze

Effect of L-Cysteine on Micro-Galvanic Corrosion of ADC12 Aluminum Alloy in a Low-Conductivity Coolant for Electric Vehicles

Study on Inhibition Behavior of Aluminum-Based Detergent

Corrosion inhibition, long-term and adsorption mechanisms of humic acid on ADC12 aluminum alloy in oxalic acid solution

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Durable slippery liquid-infused porous surfaces for effective corrosion protection of aluminum alloy in ethylene glycol-water solutions

Temporal Aspects of Corrosion Inhibition on Copper, Silver, and Copper-Silver Alloy: An Electrochemical Impedance Spectroscopy Study

Femtosecond laser fabrication and chemical coating of anti-corrosion ethylene-glycol repellent aluminum surfaces

Corrosion Development Between Liquid Gallium and Four Typical Metal Substrates Used in Chip Cooling Device

Surface Super-Hydrophobicity of Aluminum Alloy and its Corrosion and Anti-Icing Properties

Excellent performance of dodecyl dimethyl betaine and calcium gluconate as hybrid corrosion inhibitors for Al alloy in alkaline solution

Manufacturing Feasibility of All-Aluminum Automotive Engines Via Application of High Silicon Aluminum Alloy

Corrosion Inhibitor Screening For Aa6014 Aluminum Alloy Under Different Ambient Conditions Using A Novel Multielectrode Methodology

Corrosion effects and reliability improvement of silver wire bonded contacts in automotive application

Corrosion Resistance of P2 Inhibitor Treatment of Aluminum Alloy

The Corrosion Inhibition Effect on Fatigue Behavior for Aluminum Alloy 5052 in the Saline Environment

Microstructural and Electrochemical Study: Pitting Corrosion Mechanism on A390 Al–Si Alloy and Ce–Mo Treatment as a Better Corrosion Protection