Abstract:Polyether ether ketone (PEEK) has been considered as an alternative material to cobalt chrome in the femoral component of a total knee replacement. In this article, the experimental simulation of torsion wear for a PEEK and CoCr femoral head against an ultra-high-molecular-weight polyethylene (UHMWPE) tibial pad was carried out using a two-station knee simulator. The testing results showed that T-θ curves of torsion wear for PEEK-on-UHMWPE bearing couples showed three types of morphological characteristics, such as linear, elliptical, and parallelogram shapes. With an increase in torsion angular displacement, T-θ curves changed from the linear to the parallelogram type, and the relative motion state changed from the partial slip regime coordinated by the elastic deformation to the slip regime with plastic deformation. With an increase in normal load, the T-θ curve changed from the parallelogram to the elliptical type, and the relative motion state changed from the slip regime to the mixed slip regime. Under intermediate torsion wear conditions, the wear factors of UHMWPE were 11.25 ± 2.08 × 10−6 mm3/C and 14.65 ± 2.49 × 10−6 mm3/C against PEEK and CoCr. Under high torsion wear conditions, the wear factors were 20.51 ± 3.23 × 10−6 mm3/C and 23.26 ± 3.01 × 10−6 mm3/C, respectively. The wear surface of UHMWPE against PEEK showed slight adhesive wear and plastic deformation in the center, and abrasive wear with local fatigue spalling was found at the edges. The wear topographies presented characteristics similar to the CoCr bearing combination.

Wear and Transmission Error between PEEK Bush and 7075 Aluminium Alloy Cam Plate Components in Robot Joints

Tribological behavior of modified polyetheretherketone composites in sliding against stainless steel under water lubrication

Relationship between Load, Rotation Speed and, Strength in All - PEEK and PEEK Race – PTFE Retainer Hybrid Polymer Bearings under Dry Rolling Contact Fatigue

An Experimental Investigation on the Wear of Lubricated Steel Against PEEK Gears

Comparison of Friction and Wear Performances of Pure Poly-ether-ether-ketone Polymer and Carbon Fiber Reinforced Poly-ether-ether-ketone Polymer Composite for Bushing and Bearing Applications

Influence of Radial Load on PEEK Plastic Bearings Life Cycle under Water Lubricated Conditions

Wear mechanism and debris analysis of PEEK as an alternative to CoCrMo in the femoral component of total knee replacement

A study on improving friction and wear performance of bearing bush in radial piston hydraulic motor

Effect of PTFE Retainer on Friction Coefficient in Polymer Thrust Bearings under Dry Contact

Study of Friction and Wear Characteristics of PEEK by Reciprocating Sliding Experiment and Temperature Dependences Simulation

Tribological behavior of PEEK components with compositionally graded PEEK/PTFE surfaces

Influence of Cross-Shear and Contact Pressure on Wear Mechanisms of PEEK and CFR-PEEK in Total Hip Joint Replacements

Tribological Performance Study of Low-Friction PEEK Composites under Different Lubrication Conditions

Torsion Wear Behavior of PEEK-on-UHMWPE as an All-Polymer Joint Combination in Total Knee Replacement

Fretting Wear Study of PEEK-Based Composites for Bio-implant Application

Optimization and tribological performance of PEEK based composite coatings reinforced with PTFE for friction pairs of aviation hydraulic pumps

Tribological Properties of PEEK and Its Composite Material under Oil Lubrication

Friction Coefficient and Wear of PEEK-PTFE Hybrid Radial Ball Bearings under Dry Conditions

Determination of the Effect of Sliding Speed on Tribological Performances of Carbon Fiber Reinforced, Graphite and PTFE Filled Poly-ether-ether-ketone (PEEK) Polymer Composite

Study on the Tribological Behaviors of Different PEEK Composite Coatings for Use As Artificial Cervical Disk Materials

Friction and wear performance of polyether ether ketone (PEEK) polymers in three lubrication regimes