Abstract:Introduction. Over the last decade, composite materials based on polytetrafluoroethylene (PTFE) have been increasingly used as alternative materials for automotive applications. PTFE is characterized by a low coefficient of friction, hardness and corrosion resistance. However, this material has a high wear rate. A group of researchers attempted to improve the wear resistance of PTFE material by reinforcing it with different fillers. The purpose of the work: This study experimentally investigates the dry sliding wear characteristics of a PTFE composite reinforced with carbon fiber (35 wt.%) compared to SS304 stainless steel. In addition, experimental mathematical and ANN models are developed to predict the specific wear rate, taking into account the influence of pressure, sliding speed, and interface temperature. The methods of investigation. Dry sliding experiments were performed on a pin-on-disk wear testing machine with varying the normal load on the pin, disk rotation, and interface temperature. Experiments were planned systematically to investigate the effect of input parameters on specific wear rates with a wide range of design space. In total, fifteen experiments were carried out at a 5-kilometer distance without repeating the central run experiment. Sliding velocities were obtained by selecting the track diameter on the disk and corresponding rotation of the disk. A feedforward back-propagation machine learning algorithm was used to the ANN model. Results and Discussion. This study finds better prediction accuracy with the ANN architecture having two hidden layers with 150 neurons on each layer. This study finds an increase in specific wear rates with normal load, sliding velocity, and interface temperature. However, the increase is more prominent at higher process parameters. The normal load followed by sliding velocity most significantly affects the specific wear rate. The results predicted by the developed models for specific wear rates are in good agreement with the experimental values with an average error close to 10%. This shows that the model could be reliably used to obtain the wear rate of PTFE composite reinforced with carbon fiber (35 wt.%) compared to SS304 stainless steel. This study finds scope for further studies considering the effect of varying ANN architectures, different amount of neurons, and hidden layers on the prediction accuracy of the wear rate.

Determination of the Effect of Sliding Speed on Tribological Performances of Carbon Fiber Reinforced, Graphite and PTFE Filled Poly-ether-ether-ketone (PEEK) Polymer Composite

Tribological behavior of modified polyetheretherketone composites in sliding against stainless steel under water lubrication

Comparison of Friction and Wear Performances of Pure Poly-ether-ether-ketone Polymer and Carbon Fiber Reinforced Poly-ether-ether-ketone Polymer Composite for Bushing and Bearing Applications

Effect of filling materials on the tribological performance of polytetrafluoroethylene in different wear modes

Effect of PTFE Retainer on Friction Coefficient in Polymer Thrust Bearings under Dry Contact

Performance and mechanisms of different tribological thermoplastic composites in sliding contact with steel

Comparative Study on the Frequency and Wear of Thermoplastic Polymeric Materials Based on PTFE

Tribological Performance Study of Low-Friction PEEK Composites under Different Lubrication Conditions

Tribological Properties Of Polytetrafluoroethylene-Based Composite In Different Lubricant Media

Study on the Friction and Sliding Wear Behavior of Hybrid Polytetrafluoroethylene/Kevlar Fabric Composites Filled with Polyphenylene Sulfide

Modeling of sliding wear characteristics of Polytetrafluoroethylene (PTFE) composite reinforced with carbon fiber against SS304

Large-scale tests on friction and wear of engineering polymers for material selection in highly loaded sliding systems

Tribological Behaviors of Several Polymer–polymer Sliding Combinations under Dry Friction and Oil-Lubricated Conditions

Friction and wear performance of polyether ether ketone (PEEK) polymers in three lubrication regimes

Tribological performance of polymer composites used in electrical engineering applications

Tribology of self-lubricating high performance ATSP, PI, and PEEK-based polymer composites up to 300 °C

Comparative Evaluation of Tribological Effectiveness of Carbon- and Glass-Filled Polyamide Composites Using Submicromechanical Diagnostics of Surface Layers before and after Wear Tests during Dry Sliding Friction

The effects of filler type on the friction and wear performance of PEEK and PTFE composites under hybrid wear conditions

Tribological Behavior of Reinforced PTFE Composites and Un-Reinforced Polyketone-Based Materials against Coated Steel

Tribological properties of PTFE/Kevlar fabric composites under heavy loading

Physical and Chemical Evolution of PTFE-α-Al2O3 Composites Versus 304 SS Tribofilms During Dry Sliding