Abstract:The use of high strength low alloy steels provides several potential advantages including lower weight, lower manufacturing costs, and ease of handling and transport. The progress in steel manufacturing technology has continually called for new developments in welding processes and consumables to produce weld metal deposits with mechanical properties essentially equivalent to the base metal. Controlling the weld metal microstructures as well as raising the welding productivity is critical factor for the development of weld metal of high strength steel to secure satisfactory mechanical properties and to reduce production costs. In order to meet the demand to apply 1000 MPa class steel to the fabrication of large scale steel structures, a weld wire for the 1000 MPa class steel has been under development to obtain the required strength and toughness, which depend primarily on the microstructure. In this work, the effects of shielding gas composition on the microstructure and properties of 1000 MPa grade deposited metals produced by metal active gas (MAG) welding have been investigated. The shielding gas employed was a mixture of argon (Ar) and carbon dioxide (CO2) (5%similar to 30%), and the weld heat input was 13 kJ/cm. The properties of deposited metal with shielding gas of 80%Ar+20%CO2 is the best, the yield strength is 980 MPa, meanwhile, its Charpy absorbed energy at room temperature and -40 degrees C are 72.6 and 52 J, respectively. The results show that the microstructure of the deposited metal, consisting primary of low carbon martensite and a few parallel bainite plate, became more interweaved bainitic packets as the CO2 content of the shielding gas was increased. The initial bainite nucleated at austenite grain boundaries and subsequent bainite plates can form at the oxide inclusions of intragranular, which presented an intersected configuration and the microstructure was refined. The content of bainite palte and distribution morphology of martensite/bainite is the intrinsic reason attributed to mechanical properties of deposited metals. The content of bainite for deposited metal has an optimal proportion and more isn't necessarily better. It was also found that the area fraction, the size and the compositions of oxide inclusions in deposited metals were changed with increasing CO2 content. The deposited metal as using 70%Ar+30%CO2 has the minimum toughness because more large size oxide inclusions formed which are known to be harmful to the toughness.

Optimization of welding conditions for hot-wire GMAW with CO2 shielding on heavy-thick butt joint

High-Efficiency and Low-Heat-Input CO2 Arc-Welding Technology for Butt Joint of Thick Steel Plate Using Hot Wire

Selection of Welding Conditions for Achieving Both a High Efficiency and Low Heat Input for Hot-Wire Gas Metal Arc Welding

Performance optimization and investigation of metal-cored filler wires for high-strength steel during gas metal arc welding

Thick-wire GMAW for fusion welding of high-strength steels

Effects of Shielding Gas on GMAW of 10ni5crmov HSLA Steel Using High Cr-Ni Austenitic Wire

Influence of metal transfer behavior under Ar and CO2 shielding gases on geometry and surface roughness of single and multilayer structures in GMAW-based wire arc additive manufacturing of mild steel

Effects of Shielding Gases on Process Stability of 10crni3mov Steel in Hybrid Laser-Arc Welding

Bead shape control in high-speed fillet welding using hot-wire GMA laser hybrid welding technology

Feasibility study on tandem narrow gap GMAW of 65 mm thick steel plate

Effect of shielding gas on MIG welding performance with austenitic wire

Optimization of shielding gas composition in high nitrogen stainless steel gas metal arc welding

Study on multipass welding of thick section steels using CO2 laser welding

Joint performance of CO2 laser-MIG hybrid welding 5083-H116 alloy

Influence of the CO2 content on operational performance of short-circuit GMAW

High Efficiency and Quality of Multi-Pass Tandem Gas Metal Arc Welding for Thick Al 5083 Alloy Plates

Optimising the quality of several welds in a metal-inert gas arc joining of AA6082 and AA7075 using the grey-based Taguchi technique

Study and Application of Process Performance and Welding Wire of CO2 Welding and MAG Welding

EFFECT OF SHIELDING GAS ON MICROSTRUCTURE AND PERFORMANCE OF 1000 MPa GRADE DEPOSITED METALS

Experimental Investigation of the Impact of GMAW Welding Parameters on the Mechanical Properties of AISI 316L/ER 316L using Quaternary Shielding Gas

Influence of Shielding Gas on Microstructure and Mechanical Properties of Laser Welded–brazed Al/steel Lapped Joint