Abstract:Abstract Microstructural evolution occurs in lead free Sn-Ag-Cu (SAC) solder joints exposed to isothermal aging. Such changes lead to degradations in the mechanical properties and creep behavior of the solder, and can result in dramatic reductions in the board level reliability of lead-free electronic assemblies subjected to aging. In our recent research, Scanning Electron Microscopy (SEM) has been used to: (1) monitor aging induced microstructural changes occurring within fixed regions in selected lead-free solder joints, (2) create time-lapse imagery of the microstructure evolution, and (3) analyze the microstructural changes quantitatively and correlate to the observed mechanical behavior evolution. This approach has removed the limitations of many prior studies where aged and non-aged microstructures were taken from two different samples and could only be qualitatively compared. In our current study, the microstructural evolutions were observed in SAC305 (96.5Sn-3.0Ag-0.5Cu) and SAC_Q (SAC+Bi) exposed to isothermal conditions at T = 100 °C and 125 °C for several different regions from several different joints. The microstructures in several fixed regions of interest were recorded after predetermined time intervals of aging, which were 1 hour (up to 270 hours) and 250 hours (up to 7000 hours) for the long-term aging samples. The aging induced changes in microstructure have been correlated with the changes in mechanical behavior measured using uniaxial tensile testing. The area and diameter of each IMC particle were tracked during the aging process using the recorded images and imaging processing software. As expected, the analysis of the evolving SAC305 and SAC+X microstructures showed a significant amount of diffusion of silver and bismuth in the beta-tin matrix during aging. In particular, Ag3Sn particles coalesced during aging leading to a decrease in the number of particles. Any bismuth in the SAC+X microstructure was observed to quickly go into solution, resulting in solid solution strengthening. This primary occurred within the beta-Sn dendrites, but also in the Ag3Sn intermetallic rich regions between dendrites. The presence of bismuth in was also found to slow the diffusion process that coarsens the Ag3Sn IMC particles. The combination solid solution strengthening and a lower diffusion rate for Ag lead to reduced aging effects in the SAC+Bi alloy relative to the SAC305 solder alloy. The SAC_Q alloy was found to have significantly better high temperature mechanical properties relative to SAC305 at all prior aging conditions. In particular, the initial modulus and ultimate tensile strength of SAC305 experienced large degradations during high temperature aging, whereas the same properties of SAC_Q changed only slightly. These changes in mechanical behavior correlated well with the observed increases in the average IMC particle diameter and decreases in the number of IMC particles. The microstructural and material property degradations were especially large for SAC305 during the initial 50 hours of aging.

Effect of Aging on Power Integrity and Conducted Emission of Digital Integrated Circuits

Computational Analysis of Mechanical and Electromigration Reliability Problems

Progress Review of Electromagnetic Compatibility Analysis Technologies for Packages, Printed Circuit Boards, and Novel Interconnects

Analysis and Modelling of Passive device degradation for a long-term electromagnetic emission study of a DC-DC converter

Passive device degradation models for an electromagnetic emission robustness study of a buck DC-DC converter

Electromagnetic radiation study of Intel Dual Die CPU with heatsink

Aging in CMOS RF Linear Power Amplifiers: Experimental Comparison and Modeling

Compact Modeling and Simulation of Accelerated Circuit Aging

Impact of Mechanical Property Degradation and Intermetallic Compound Formation on Electromigration-Oriented Failure of a Flip-Chip Solder Joint

Concurrent device/circuit aging for general reliability simulations

Impact of Technological Trends and Electromagnetic Compatibility of Integrated Circuits

High temperature aging of epoxy-based molding compound and its effect on mechanical behavior of molded electronic package

Chip Metallization Aging Monitoring with Induced Voltage Vee Between Kelvin and Power Emitter for High Power IGBT Modules

Accelerated Aging in Analog and Digital Circuits with Feedback

Investigation and Comparison of Aging Effects in SAC305 and Doped SAC+X Solders Exposed to Isothermal Aging

Statistical Reliability Analysis under Process Variation and Aging Effects

Aging-temperature-and-propagation Induced Pulse-Broadening Aware Soft Error Rate Estimation for Nano-Scale CMOS

Dielectric Characteristic Analysis and Insulation State Evaluation of Packaging Material for Power Module with Different Aging Degrees

An Advanced Design of Power Module with EMI Reduction Method

Unified Self-Heating Effect Model for Advanced Digital and Analog Technology and Thermal-Aware Lifetime Prediction Methodology

An Improved Stress-strain Model Considering the Aging Effect of Solder Layers