Abstract:Abstract — Fluorocarbon ‘O’-rings to DTD5612A:1982 have been used for many years for sealing at −40°C. The UK Department for Transport (DfT) issued a letter on 12 March 2001 raising concerns over the suitability of these ‘O’-rings for service temperatures down to −40°C as required by the regulations for certain types of packages containing radioactive material, and requested that the technical justification for continued use was reviewed. Gravatom Engineering Systems Ltd performed a low-temperature test, at Harwell, using design no 3406 with new fluorocarbon ‘O’-rings and bolts. The test proved that these ‘O’-rings are not suitable for temperatures down to −40°C since the seals would not hold a vacuum at temperatures lower than −24°C. This necessitated an investigation to find a suitable ‘O’-ring material with a leak rate pelformance of 10−5 Pa.m3. s−1 SLR at −40°C to +330°C since this represents the widest temperature range of the AWE Type B(U) containers. Various seal manufacturers were contacted, and following further investigation two seal materials presented themselves as possible options: Viton GLT, a fluorocarbon manufactured by Parker-USA (Parker compound V0835–75) with CEETAK Ltd acting as agents in the UK, and EPDM-30H developed by BNFL and manufactured by James Walker & Co Ltd. Following testing, the EPDM-30H seals proved to be the most suitable sealing material option for an operating temperature range of −40°C to +330°C. The seal achieved a leak rate at −40°C of better than 8.0 × 10−10 Pa.m3.s−1 which is well within the equivalent target leak rate of less than 1.2 × 10−4 Pa. m3.s−1. The seals also remained effective down to at least −50°C with no loss in sealing pelformance. A leak rate of better than 7.2 × 10−6 Pa.m3.s−1. was achieved at +330°C which is within the target leak rate of less than 6.4 × 10m−5 Pa.mm3.s−1. The interspace pressure increased slightly during heating, but recovered fully on cooling to give a leak rate at ambient temperature of 1.0 × 10−10 Pa.mm3.s−1. The EPDM-30H seals proved satisfactory at high temperature, with excellent recovery on cooling. It was concluded that EPDM-30H seals may be used as a direct replacement for Viton where the temperature range does not exceed −40°C to +330°C and where the higher temperature of that range is of relatively short duration (i.e. less than 24 h).

Comparison of permeation of atmospheric gases through Viton O-ring gaskets for different initial conditions

Study on Permeation of Acetone/Nitrogen Mixed Gas Through Al2o3 Microporous Membranes: Molecular Dynamics

Experimental Study of Pressure Drop-Flow Rate Characteristics of Heated Tight Porous Materials

Investigation into Replacement of Viton ‘O’-Rings

Investigation of Viton O-Ring Performance for the SABRE Dark Matter Experiment

Measurement of Reactive and Condensable Gas Permeation Using a Mass Spectrometer

Air Leakages at Microvalves: Pressure Decay Measurements and Extended Continuum Modelling of Knudsen Flows

Relationship between fluctuating differential pressure and void fraction of gas-liquid two-phase flow in Venturi tube

Review of Developed Methods for Measuring Gas Uptake and Diffusivity in Polymers Enriched by Pure Gas under High Pressure

Permeation of Compressed and Supercritical Fluids Through Porous Membranes

Outgassing rate comparison of seven geometrically similar vacuum chambers of different materials and heat treatments

Investigating the influence of operating variables on sealing performance of a V-ring seal stack in the oil and gas industry for enhanced environmental and operational performance

Air, Helium and Water Leakage in Rubber O-ring Seals with Application to Syringes

Identification of swelling/shrinking coefficients under CO2 on an FKM O-ring – Comparison with HNBR and influence of reinforcements on the matrices

Practical Sealing for Common Gasket Materials and Construction Types

Flow Characteristics of Gas Permeation Through a PVF Porous Tube

Low-pressure gas flow properties of sintered stainless steel microporous media

Prediction of gas flow in compressible and low permeability porous media

Modelling of Fluid Permeability at the Interface of the Metal-to-Metal Sealing Surface

Compatibility and Interaction Mechanism between the C 4 F 7 N/CO 2 /O 2 Gas Mixture and FKM and NBR

Moist Air Permeability Characteristics of Flexible Contact Gaskets Used in Refrigerators