Abstract:Abstract. The storage of spent fuel and high-level radioactive waste in Germany is performed in interim storage containers with double-lid systems. The lids are bolted and equipped with metal seals (e.g. Helicoflex®) to ensure the safe containment of the inventory. The used metal seals have a layered structure consisting of three components as can be seen schematically in the cross-sectional view in Fig. 1. In the centre, a helical spring is positioned that is surrounded by two C-shaped jackets and is mainly responsible for generation of the required restoring force. The inner jacket is made of stainless steel and homogenises the restoring force of the helical spring. The outer jacket is made of silver or aluminium which are both soft metals in comparison to the contact partners (lid and container body). During bolting of the lid to the container body, the seal is compressed. The generated restoring force of the helical spring causes a plastic deformation of the outer jacket and adapts to the surfaces of the lid and the container body. Hence, leakage paths are closed, and the sealing function is generated. Typical durations for existing interim storage licenses in Germany are 40 years, but it can be expected that they have to be extended to longer periods as a final repository will not be available before the end of the running licence periods. This extension of licence periods requires a solid understanding of the long-term behaviour of the seals under storage conditions. To meet this challenge, long-term investigations were started at the Bundesanstalt für Materialforschung und -prüfung (BAM) in 2009. These tests focus on seals assembled in test flanges which are stored at temperatures ranging from room temperature to 150 ∘C for accelerated ageing. The aged seals are tested repeatedly after certain ageing steps, and the leakage rate (as indicator for sealing performance), the remaining seal force, and the useable resilience upon decompression are determined. An update on the performed investigations with respect to earlier publications (Grelle et al., 2019; Goral et al., 2023) will be given, and the implications of the results for resilient, long-term safety will be presented. Additionally, there will be a focus on the currently planned further investigations, and the following question will be addressed. What is additionally needed for evaluation of an interim storage period extension in regard to the used metal seals?

Investigation of Viton O-Ring Performance for the SABRE Dark Matter Experiment

Experimental study on the performance of cryogenic seal structure with indium

Investigation into Replacement of Viton ‘O’-Rings

Comparison of permeation of atmospheric gases through Viton O-ring gaskets for different initial conditions

Development of vacuum seals for diagnostic windows of the International Thermonuclear Experimental Reactor

Characterization of long-term evolution of leakage rates of O-ring seals in nuclear power plant under high-temperature and high-pressure conditions

Design and performance of indium seals for size-constrained tunable laser spectrometers

Evaluating the thermal, mechanical and swelling behavior of novel silicone and polyurethane additively manufactured O-rings in the presence of organic liquids and military fuels

Enhancement of Light Yield and Stability of Radio-Pure Tetraphenyl-Butadiene Based Coatings for VUV Light Detection in Cryogenic Environments

The Shock Induced Mechanical Response of the Fluorinated Tri-polymer, Viton B

Temperature Dependence of the Mechanical Dissipation of Gallium Bonds for Use in Gravitational Wave Detectors

Investigating the influence of operating variables on sealing performance of a V-ring seal stack in the oil and gas industry for enhanced environmental and operational performance

Long-term sealing performance evaluation and service life prediction of O-rings under thermal-mechanical coupling conditions

Investigations of aged metal seals for transport package safety assessment

Materials for Ultrahigh Pressure Sealing in Bridgman Anvil Devices

The SABRE South Technical Design Report Executive Summary

Leakage analysis of B shape ring self-energized seal in high pressure polythene polymerizer due to the aging of its nonmetallic ring

Leakage analysis and ground tests of the O-type rubber ring seal applied in lunar sample return devices

Investigations of aged metal seals for interim storage

Effect of Butadiene Rubber Crystallization on Low-Temperature Properties of Butadiene/Silicone Rubber Blends with Potential for Mars Applications

Fe0.79Si0.07B0.14 metallic glass gaskets for high-pressure research beyond 1 Mbar