Abstract:A detailed micromechanical finite element analysis methodology is presented to predict the transverse tensile (fiber perpendicular) failure behavior of a unidirectional (UD) glass fiber-reinforced plastic composite ply. In order to understand the constituent-level stress–strain and damage behavior, finite element analysis is accomplished using representative volume element (RVE) that consists of random fiber distribution as observed in the microscopic image of an actual composite ply. For modeling the fiber/matrix interface failure behavior, cohesive zone module (cohesive surface/cohesive element) of Abaqus® is used. In order to capture the epoxy matrix stiffness and strength degradation, the following two different approaches are used: (i) initially, the linear Drucker–Prager plasticity model in combination with a ductile fracture criterion is used; (ii) later, a brittle failure approach such as the quadratic normal stress criterion within the framework of eXtended finite element method is used. From the detailed micromechanical analysis of the RVE, it is observed that the initial damage in the RVE occurs in the form of fiber/matrix interface decohesion. With increasing tensile load, interface crack propagates and creates a stress concentration region in the matrix material, adjacent to the crack tip. Further load application causes both interface crack tip and matrix stress concentration to move away from the load application direction. As soon as the interface crack tip reaches approximately 60° to 70° away from the load application direction, the conjunction of the matrix damage with the interface crack leads to the RVE final failure. The predicted average stress–strain curves from the above-mentioned two different epoxy matrix failure criterions (ductile and brittle) correlate very well with the experimental results, indicating that the brittle failure behavior of a UD fiber-reinforced plastic composite ply under transverse tensile load is mainly controlled by the fiber/matrix interface properties.

Fatigue accumulated damage in notched quasi-isotropic composites under high-temperature conditions: A discussion on the influence of matrix nature on the stress energy release rate

Comparison of the in situ compressive behavior of carbon fibers woven ply laminates exposed to one‐sided heat flux: Thermoplastic versus thermosetting composites

A New Approach for Studying Fatigue Damage

A New Approach to Low-Cycle Fatigue Damage Based on Exhaustion of Static Toughness and Dissipation of Cyclic Plastic Strain Energy During Fatigue

The fatigue damage mechanics of a carbon fibre composite laminate: I—development of the model

A damage model for matrix cracks in composite laminates under fatigue loading based on continuum damage mechanics

Experimental Research on Fatigue Behavior of Composites Using Energy Dissipation Methodology

A 3D finite element model to simulate progressive damage in unidirectional- and woven-fibre thermoplastic discontinuous-long-fibre composites

Modeling of Damage Evolution and Failure in Fiber-Reinforced Ductile Composites under Thermomechanical Fatigue Loading

Damage development in woven carbon fibre thermoplastic laminates with PPS and PEEK matrices: A comparative study

Evaluation and Modeling of the Fatigue Damage Behavior of Polymer Composites at Reversed Cyclic Loading

On Static and Fatigue Strength Determination of Carbon Fibre/epoxy Composites Part 1: Experiments

Stress-dependence and Time-Dependence of the Post-Fatigue Tensile Behavior of Carbon Fiber Reinforced SiC Matrix Composites

Low-cycle Fatigue Behavior and Damage Progression of a Fiber Reinforced Titanium Matrix Composite

A Damage-Based Fatigue Model of Braided Ceramic Matrix Composites at Elevated Temperature

Temperature-Dependent Fatigue Damage Evolution of Fiber-Reinforced Ceramic-Matrix Composites

Mechano-chemical molecular chains model of fatigue damage for fibre-reinforced polymeric matrix composites

Computational micromechanical modeling of transverse tensile damage behavior in unidirectional glass fiber-reinforced plastic composite plies: Ductile versus brittle fracture mechanics approach

Evaluation of matrix crack growth in interlaminar toughened quasi-isotropic carbon-fiber reinforced plastic laminates up to the very-high cycle regime by ultrasonic fatigue testing

Progressive Fatigue Modelling of Open-Hole Glass-Fibre Epoxy Laminates

Modeling of progressive high-cycle fatigue in composite laminates accounting for local stress ratios