Abstract:In recent decades, in order to replace traditional synthetic polymer composites, engineering research has focused on the development of new alternatives such as green biocomposites constituted by an eco-sustainable matrix reinforced by natural fibers. Such innovative biocomposites are divided into two different typologies: random short fiber biocomposites characterized by low mechanical strength, used for non-structural applications such as covering panels, etc., and high-performance biocomposites reinforced by long fibers that can be used for semi-structural and structural applications by replacing traditional materials such as metal (carbon steel and aluminum) or synthetic composites such as fiberglass. The present research work focuses on the high-performance biocomposites reinforced by optimized sisal fibers. In detail, in order to contribute to the extension of their application under fatigue loading, a systematic experimental fatigue test campaign has been accomplished by considering four different lay-up configurations (unidirectional, cross-ply, angle-ply and quasi-isotropic) with volume fraction Vf = 70%. The results analysis found that such laminates exhibit good fatigue performance, with fatigue ratios close to 0.5 for unidirectional and angle-ply (±7.5°) laminates. However, by passing from isotropic to unidirectional lay-up, the fatigue strength increases significantly by about four times; higher increases are revealed in terms of fatigue life. In terms of damage, it has been observed that, thanks to the high quality of the proposed laminates, in any case, the fatigue failure involves the fiber failure, although secondary debonding and delamination can occur, especially in orthotropic and cross-ply lay-up. The comparison with classical synthetic composites and other similar biocomposite has shown that in terms of fatigue ratio, the examined biocomposites exhibit performance comparable with the biocomposites reinforced by the more expensive flax and with common fiberglass. Finally, appropriate models, that can be advantageously used at the design stage, have also been proposed to predict the fatigue behavior of the laminates analyzed.

Fatigue resistance of ultra-high-modulus pitch-based carbon fiber/epoxy composites under tensile loading

Study on Flexural Fatigue Life of Ultra-High Toughness Cementitious Composites under Constant Amplitude Cyclic Loading

Tensile fatigue response of a novel carbon/flax/epoxy hybrid composite under strain-controlled and stress-controlled amplitude

Static and Fatigue Tensile Properties of Cross-Ply Carbon-Fiber-Reinforced Epoxy-Matrix-Composite Laminates with Thin Plies

Tension-tension fatigue properties of multiaxial laminated carbon/epoxy composites molded by high-pressure resin transfer molding (HP-RTM) process

Static and fatigue behavior of basalt fiber-reinforced thermoplastic epoxy composites

Fatigue behavior of symmetric and asymmetric carbon and basalt fiber-reinforced polymer composites in transverse loading

Fatigue accumulated damage in notched quasi-isotropic composites under high-temperature conditions: A discussion on the influence of matrix nature on the stress energy release rate

Mechanical performance of carbon-epoxy laminates. Part II: quasi-static and fatigue tensile properties

Analysis of fracture state and fatigue life of high modulus carbon fiber wrapped composite barrel

Fatigue Behaviour of High-Performance Green Epoxy Biocomposite Laminates Reinforced by Optimized Long Sisal Fibers

A micromechanical study of the fatigue behavior of MWCNT-modified carbon fibers/epoxy resin single filament composites subjected to cyclic loadings

Tensile Fatigue Behavior of Polyester and Vinyl Ester Based GFRP Laminates—A Comparative Evaluation

Flexural Properties of Carbon/Glass Hybrid Thermoplastic Epoxy Composite Rods Under Static and Fatigue Loadings

Elevated temperature effect on tension fatigue behavior and failure mechanism of carbon/epoxy 3D angle-interlock woven composites

Prediction of Fatigue Life of Polyetherimide/Carbon Fiber Particulate Composites at Various Maximum Stresses and Filler Contents

An unexpected hardening behaviour of carbon-fiber epoxy composites under flexural fatigue loading and its intensification by graphene nano-fillers

Study of the Fatigue Behavior of the Unidirectional Zylon/epoxy Composite Used in Pulsed Magnets

Fatigue and durability assessment of PA6-based carbon fiber composites for lightweight applications

Review: Fatigue of Fiber-Reinforced Composites, Damage and Failure

Accelerated estimation of the very high cycle fatigue strength and life of polymer composites under ultrasonic cyclic three-point bending