Abstract:Development of the layer-wise build-up of metallic materials offered significant technical and economic advantages for modern structural components. Airliners are now losing much weight which is due to efficient designs which were made possible by additive manufacturing technologies. In addition to topology optimization, selective laser melting (SLM) induces enhanced microstructural features and mechanical properties. Highly dynamic melt pools result in refined microstructures which increase the strength of the conventionally manufactured titanium and aluminum alloys. At the scanning electron microscope (SEM), it was revealed that SLM produces a very fine cellular dendritic microstructure in aluminum alloys of the Al-Si system. In the recently developed Scalmalloy, the ultra-fine ceramic precipitation of Al-Sc3 enables the tensile strength to reach 490 MPa and improves fracture strain by 100%. Along with improved microstructures due to high cooling rates, unstable melt pools induce spherical porosity as the release of gases from the powder bed is entrapped by the high solidification rate. Platform heating (PH) which slows down cooling and enhances energy density is proved to stabilize melt pools and improve the degassing mechanism. Al-Si alloys are well-known cast alloys in the automotive industry; however, with the application of SLM technology, the tensile strength of these alloys is now 200% of the cast counterparts. The interest of aerospace industry in a high-strength aluminum alloy encouraged the development of Scalmalloy which has a similar tensile strength to the wrought EN AW 7075. The latter is sensitive to hot cracking during SLM. For assurance of quality of additively manufactured alloys for the aerospace industry, the non-destructive testing (NDT) technology of X-ray computed tomography (CT) is applied in this study to develop finite element (FE) models which will be used in a statistical simulation to deduce a quality-controlled fatigue strength in highand very high-cycle fatigue (HCF to VHCF) regimes. Modeling of fatigue strength will be based on the quasistatic and cyclic deformation behavior of SLM aluminum alloys.

Comparison of Microstructure and Mechanical Properties of Scalmalloy® Produced by Selective Laser Melting and Laser Metal Deposition

Fatigue properties of Scalmalloy® processed by laser powder bed fusion in as-built, chemically and conventionally machined surface condition

An Improved Process Scan Strategy to Obtain High-Performance Fatigue Properties for Scalmalloy®

Quality assurance of additively manufactured alloys for aerospace industry by non-destructive testing and numerical modeling

Processing of Al-Sc aluminum alloy using SLM technology

Microstructure Evolution and Mechanical Property Response of 3D-Printed Scalmalloy with Different Heat-Treatment Times at 325 °C

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Influence of coherent intermetallic nano-precipitates on the nano-level mechanical and tribological properties of the Laser-Powder bed fused Scalmalloy

Selective Laser Melting of Gas Atomized Al–3.02Mg–0.2Sc–0.1Zr Alloy Powder: Microstructure and Mechanical Properties

Fatigue Crack Growth Behavior of Al-4.5Mg-0.6Sc-0.3Zr Alloy Processed by Laser Powder Bed Fusion

Effect of the heat treatment on the mechanical properties and microstructure of Scalmalloy® manufactured by Selective Laser Melting (SLM) under certified conditions

Role of nitrogen and helium gases on microstructure and anisotropic mechanical properties of cold-sprayed scalmalloy deposits

Thermal and mechanical properties of an Al-Mg-Sc-Zr high strength alloy fabricated by selective laser melting

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

A detailed microstructural and corrosion analysis of an additively manufactured magnesium alloy produced by selective laser melting

Microstructure and mechanical properties of Al-Fe-Sc-Zr alloy additively manufactured by selective laser melting

Microstructure-induced anisotropic tribological properties of Sc-Zr modified Al–Mg alloy (Scalmalloy®) produced via laser powder bed fusion process

Process-Dependent Composition, Microstructure, and Printability of Al-Zn-Mg and Al-Zn-Mg-Sc-Zr Alloys Manufactured by Laser Powder Bed Fusion

Mechanical Anisotropy Investigated in the Complex SLM‐Processed Sc‐ and Zr‐Modified Al–Mg Alloy Microstructure

Fatigue characteristics of a newly developed laser powder bed fused scandium-free Al-Mg-Zr-Mn alloy

Developing a high-strength Al-Mg-Si-Sc-Zr alloy for selective laser melting: Crack-inhibiting and multiple strengthening mechanisms