Abstract:Additive manufacturing (AM) technology for metallic alloys such as laser powder bed fusion (LPBF) brings tremendous opportunities for development of novel alloys specifically designed for AM that would desensitize the inherent process variability and requires a refined understanding of processing–structure–property relationship that would contribute to future alloy development. In this study, two different alloys, Al-6Zn-2Mg and Al-6Zn-2Mg-0.7Sc-0.3Zr in wt. pct, representing traditional and AM-specific novel aluminum alloys, respectively, were manufactured by LPBF technique using pre-alloyed gas atomized powders. The Al-Zn-Mg ternary alloys exhibited cracks at various LPBF processing parameters, primarily along the grain boundaries of the large columnar grains that extended across multiple melt pools. The severity of cracking in LPBF Al-Zn-Mg alloys was process-dependent and could be correlated to the change in alloy composition due to evaporation of Zn and Mg with high vapor pressure. The Scheil–Gulliver non-equilibrium solidification calculations showed that the Al-Zn-Mg alloys with lower Zn and Mg concentrations had smaller solidification range (i.e., ΔT) and steepness values (i.e., dT/dfs1/2$$ \left| {{\text{d}}T / {\text{d}}f_{\text{s}}^{1/2} } \right| $$ near fs1/2=1$$ f_{\text{s}}^{1/2} = 1 $$), which corresponded to a lower cracking severity. On the other hand, no cracks were observed in Al-Zn-Mg-Sc-Zr alloys, although their solidification range and steepness values were similar to the ternary Al-Zn-Mg alloys. The microstructure of Al-Zn-Mg-Sc-Zr alloys exhibited a much refined heterogeneous microstructure containing small equiaxed and columnar grains within each melt pool, owing to the heterogeneous nucleation upon primary Al3(Sc,Zr) particles. Process-dependent microstructure was observed as a result of variation in thermal gradient and cooling rate associated with LPBF parameters. Findings from this study provide guidance for the future design of AM-specific aluminum alloys and insights into the microstructural control by LPBF.

Fatigue Crack Growth Behavior of Al-4.5Mg-0.6Sc-0.3Zr Alloy Processed by Laser Powder Bed Fusion

Fatigue characteristics of a newly developed laser powder bed fused scandium-free Al-Mg-Zr-Mn alloy

Fatigue properties of Scalmalloy® processed by laser powder bed fusion in as-built, chemically and conventionally machined surface condition

An Improved Process Scan Strategy to Obtain High-Performance Fatigue Properties for Scalmalloy®

Comparison of Microstructure and Mechanical Properties of Scalmalloy® Produced by Selective Laser Melting and Laser Metal Deposition

Microstructure-induced anisotropic tribological properties of Sc-Zr modified Al–Mg alloy (Scalmalloy®) produced via laser powder bed fusion process

Microstructure, mechanical properties and fatigue crack growth behavior of an Al-Zn-Mg-Cu-Si-Zr-Er alloy fabricated by laser powder bed fusion

Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF

Process-Dependent Composition, Microstructure, and Printability of Al-Zn-Mg and Al-Zn-Mg-Sc-Zr Alloys Manufactured by Laser Powder Bed Fusion

Laser powder bed fusion of Zr-modified Al–Cu–Mg alloy: Crack-inhibiting, grain refinement, and mechanical properties

High Temperature Wear Behavior of AlMgScZr Alloy Produced By Laser Powder Bed Fusion

In-situ mechanical and microstructural characterization of miniaturized Al-Mg-Sc-Zr and AlSi10Mg specimens processed by laser powder-bed fusion (PBF-LB)

Microstructure and Fatigue Behavior of High-Performance Aluminum Alloy Al2024 Produced by Laser Powder Bed Fusion

Effect of laser alloying on the fatigue crack growth rate

Influence of LPBF-Surface Characteristics on Fatigue Properties of Scalmalloy®

Microstructural evolution modelling and low-stress fatigue performance of bimodal-structured Al-Mg-Sc-Zr alloy produced by laser powder bed fusion additive manufacturing

Influence of coherent intermetallic nano-precipitates on the nano-level mechanical and tribological properties of the Laser-Powder bed fused Scalmalloy

Cracking mechanism and its susceptibility to scanning speed during laser power bed fusion processed high-strength 2024Al alloy

Effect of Powder Spreading Parameters on Laser Absorption Behavior and Processability of High‐Strength Aluminum Alloy Fabricated by Laser Powder Bed Fusion

Effect of build direction dependent grain structure on fatigue crack growth of biomedical Co-29Cr-6Mo alloy processed by laser powder bed fusion

Microstructure, mechanical properties, and crack formation of aluminum alloy 6063 produced via laser powder bed fusion