Abstract:Using the Fully Ceramic Microencapsulated (FCM) fuel in light water reactors has multiple advantages, as it is accident tolerant because of; no hydrogen generation due to the cladding interaction with steam at high temperature, better retention of fission fragments and proliferation resistant due to very small production of transuranic elements during the burnup as compared to the standard UO2 fuel. In this study neutronics analysis of AT-FCM fuel consisting of TRISO particles embedded in SiC matrix is performed for replacement in existing VVER-1000 reactors. Standard VVER-1000 fuel assembly is transformed to Accident Tolerant Fully Ceramic Microencapsulated (AT-FCM) fuel assembly based on hydraulic diameter of the VVER-1000 assembly, the number of fuel pins are decreased with increased diameter and enrichment to conserve the initial fissile loading in AT-FCM assembly. Fuel centerline temperature of the AT-FCM assembly is found to be lower than the reference UO2 fuel assembly at the same total power produced because of the much higher thermal conductivity. FCM-TRISO fuel assembly namely Array 15 with 169 pins is proposed and analyzed. Pin cell, assembly level and full core calculations have been performed with SERPENT code using implicit and explicit models. VVER-1000 full core is modelled using the transformed FCM assembly. The embedded TRISO particles in a SiC matrix and the use of FeCrAl cladding turns out to be the perfect case for accident tolerance. High burnup of AT-FCM core in terms of MWd/kgHM for the same number of EFPDs is observed as compared to reference UO2 core due to the small breeding of transuranic elements Pu-239, Pu-240 and Pu-241. Appreciable quantity of the power is produced due to the fission of transuranic elements in reference UO2 assembly so the burnup in MWd/kgHM remains smaller than the AT-FCM fuel. Comparatively more softening of spectrum is found in AT-FCM fuel cells and assemblies towards the middle of the cycle (MOC) and End of the Cycle (EOC), this softening of spectrum tends to increase the rate of U-235 depletion. Very small quantities of plutonium isotopes are produced in AT-FCM as compared to the reference UO2 assembly because of small loading of U-238 at the BOC. The neutronics performance of AT-FCM core with burnable poison consisting of Gd2 O3 and Er2 O3 turn out to be better than reference UO2 assembly as it exhibits smooth burnup. Fuel Temperature Coefficient (FTC) and Moderator Temperature Coefficient (MTC) of the AT-FCM assembly is negative for most part of the cycle however, towards the end of cycle it becomes less negative due to small quantities of resonance absorbers, softening of thermal flux and increased rate of fission absorption in UO2 .

Analysis of SMART reactor core with uranium mononitride for prolonged fuel cycle using OpenMC

Core analysis of fully ceramic microencapsulated fuel (FCM) for SMART reactor under normal operation and reactivity insertion accident

Neutronic analysis of mixed H2O/D2O moderated SMART reactor fuel assembly with varying fractions of D2O during the fuel burnup

Simulation of uranium mononitride spent fuel: A thermodynamic approach

Neutronic analysis of fuel assembly loading patterns in small integrated pressurized water reactor core and fuel shifting strategy concept design

Fuel Performance Comparison of Uranium Nitride and Uranium Carbide in VVER-1200 using OpenMC

Neutronic Evaluation of LWR Based SMR with TRU Fuel and Comparison with Different Core Configuration of UO2 and MOX Fuel

The Use of High-Density UN Fuel in Heat-Pipe Microreactors

Feasibility of Converting NuScale SMRs from UO2 to Mixed (Pu,Th)O2 and (U,Th)O2 Cores: A Parametric Study of the Seed-Blanket Fuel Assembly

Neutronic Design and Evaluation of the Solid Microencapsulated Fuel in LWR

Design study of gas-cooled fast reactor with natural uranium as fuel employing modified CANDLE shuffling strategy in the axial direction

Particle emission from irradiated VVER-1200 fuel with Am burnable absorber

Lead-Cooled Fast Reactor Annular UN Fuel Design and Development of Performance Analysis Program

Radiological characteristics of spent nuclear fuel from small modular reactors under consideration for deployment in Ukraine

STUDY ON CRITICALITY AND NEUTRONIC SAFETY PARAMETERS OF NUSCALE FUEL ASSEMBLY

Non-uniform fuel distribution and thermo-mechanical analysis of a 1 MW thermal power micronuclear heat pipe reactor

Neutronic Characterization for a Pressurized Water Reactor Spent Fuel Assembly

Evaluation of neutronic parameters for RITM-200 reactor unit considering (238U+235U)O2, (232Th+235U)O2 and (232Th+233U)O2 dispersed fuel using MCU-PTR

Neutronic optimization of thorium-based fuel configurations f or minimizing slightly used nuclear fuel and radiotoxicity In small modular reactors

Evaluating Hydrogen-based Moderators in High-Temperature Gas-cooled Reactors with 5 wt% Enriched Uranium Annular Fuel Rods

Neutronics Analysis of VVER-1000 Core Using At-Fcm Fuel