Abstract:Schematic of sequential melting and sintering process on morphology development of UHMWPE/LDPE blends. Blending ultra‐high molecular weight polyethylene (UHMWPE) with a low molecular weight polyolefin is a well‐established technique to improve its processability. The binary blends of UHMWPE and low‐density polyethylene (LDPE) were prepared with varying LDPE content (10%, 20%, 30%, 40%, and 50% by wt.) leading to the formation of a single polymer composite system (SPCS) as melting and sintering followed preferential stages during mixing. Interestingly, the sequence of either "melting followed by sintering" or "simultaneous sintering and melting" depends on the LDPE content in the blend, resulting in unique blend morphology. Separate melting peaks for the blend's constituents were observed in thermal characterization, showing the blend's immiscibility, while intermediate peaks showed moderate miscibility in the melt state. Due to the high entanglement density, UHMWPE retained a solid‐like structure and showed an intense viscous nature even above the melting point in rheological characterization. Typically, the UHMWPE samples are fabricated by boundary fusion between particles called sintering. At LDPE content higher than 30 wt.%, the sea island structure was visible in morphological analysis, and the preexisting cavities reduced the tensile modulus by 54% in the blend, along with decreased elongation at failure (250%–100%). Similarly, the flexural modulus was reduced by 34.7% in the blends, along with the decreased flexural strength. Interestingly, the decrease in performance properties occurred in two steps over the range of LDPE content. Thus, it was clear that 30 wt.% of LDPE in the UHMWPE/LDPE blend represented the critical concentration for controlling melting and sintering sequence to develop specified morphology and performance properties. These blends have the potential for biomedical application as well as for the development of foam products, which is the further scope of the present study.

Effect of LLDPE on Aging Resistance and Thermal, Mechanical, Morphological Properties of UHMWPE/LLDPE Blends

Effect of LLDPE on Aging Resistance and Thermal, Mechanical, Morphological Properties of UHMWPE/LLDPE Blends

Enthalpy Relaxation And Embrittlement Of Poly(L-Lactide) During Physical Aging

Poly(L-Lactide) Materials with Balanced Mechanical Properties Prepared by Blending with Peg-Mb-Ppa Multiblock Copolymers

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

Abrasive wear of HDPE/UHMWPE blends

Preparation and characterization of polyethylene glycol/poly(L-lactic acid) blends

Effect of Ethylene/butyl methacrylate/Glycidyl Methacrylate Terpolymer on toughness and biodegradation of poly (l-lactic acid)

Rheology of Poly(lactic Acid)/poly(trimethylene Terephthalate) Blends Compatibilized by Clay or Maleic Anhydride-Grafted Poly(ethylene-Octene) Elastomer

The Effect of Dialkyl Peroxide Crosslinking on the Properties of LLDPE and UHMWPE

Influence of sequential melting and sintering process on morphology development and performance properties of ultra‐high molecular weight polyethylene/low‐density polyethylene blends

Ultra-high molecular weight polyethylene (UHMWPE)/high-density polyethylene (HDPE) blends with outstanding mechanical properties, wear resistance, and processability

The Effects of Chain-Extending Cross-Linkers on the Mechanical and Thermal Properties of Poly(butylene adipate terephthalate)/Poly(lactic acid) Blown Films

Studies on Linear Low-Density Polyethylene Functionalized by Ultraviolet Irradiation and Its Compatibilization

Insights on the processing and thermal degradation kinetics of PA6/PE‐g‐AA blends

Effects of thermal aging on the blend phase morphology and tribological performance of PI/UHMWPE blend composites

Effect of mixing temperature on the dispersion and degradation behaviors of HDPE/UHMWPE blends

Physical aging-induced embrittlement of PLA/PBAT blends probed by tensile test and AFM nanomechanical mapping

Physical and Thermal Properties of High-Density Polyethylene Film Modified with Polypropylene and Linear Low-Density Polyethylene

Effects of PE-g-DBM as a compatiblizer on mechanical properties and crystallization behaviors of magnesium hydroxide-based LLDPE blends

Morphological, Thermal, and Mechanical Characterization of Bio-Based High-Density Polyethylene / Biopolyamide 6.10 Blends Compatibilized with PE and SEBS Functionalized With Maleic Anhydride