Abstract:Solid oxide fuel cell (SOFC) is an energy conversion device that converts chemical energy in fuels into electric energy directly with the advantages of high efficient, clean, and wide fuel adaptability. Most hydrocarbons such as natural gas, ethane and bio-oil can be used as fuels in SOFC. When a hydrocarbon fuel, such as methane (CH4), is directly used for IT-SOFCs without prereforming by adding oxygen, steam or carbon dioxide, it is electrochemically oxidized on the triple-phase boundaries (TPB) with a strong tendency of carbon deposition in the traditional Ni-based anode. In this paper, we introduce an extra internal reforming layer on the surface of anode-support. The layer of a LaCrO3 based perovskite with exsolved Ni nanoparticles catalyst (La0.6Sr0.2Cr0.85Ni0.15O3 showed high stability in reducing atmosphere and excellent catalytic performance. Based on this, two types of anode-supported cell are fabricated by tape casting, screen printing and sintering processes. The first one is a conventional anode supported cell with a configuration of Ni-GDC/GDC/GDC-LSCF (cell 1); and the other contains a reforming layer mixed with La0.6Sr0.2Cr0.85Ni0.15O3 and SDC which was a well coking resistant promoters (cell 2). When CH4–CO2 was used as the fuel, which was supposed to yield syngas with the H2–CO ratio close to unity, the polarization resistance of the cell 1 reach at 0.247 Ω cm2 whereas the value of cell 2 is 0.082Ω cm2 at 750 °C. These results implied that both the physical and the chemical properties of the TPB have been altered drastically during internal dry reforming since that Ni-based anode show poor catalytic performance in reforming and are prone to coking. Consequently, the maximum power density for cell 1 was 470 mW cm-2 and the cell suffered from degradations during a 1 h galvanostatic operation at 1 A cm-2. The performances of the cell 2 are significantly increased above the level of the cell 1, demonstrating a peak power density at 929 mW cm-2 at 750 °C and a stable cell voltage at 1 A cm-2 and 750 °C for 48 h. Carbon deposition in the anode region of the tested cell 2 is not detected, as the La0.6Sr0.2Cr0.85Ni0.15O3 is a more active and stable catalyst than the Ni-based anode-support for dry reforming. Finally we demonstrated the strong interaction between the exsolved nanoparticles and the substrate could prevent coking deposition and proposed a promising configuration of double-layer anode for solid oxide fuel cells with on-cell reforming. Figure 1

Simultaneous Electrochemical Reduction of Carbon Dioxide and Partial Oxidation of Methane in a Solid Oxide Cell with Silver-Based Cathode and Nickel-Based Anode

Energy Storage and Syngas Production by Switching Cathode Gas in Nickel-Yttria Stabilized Zirconia Supported Solid Oxide Cell

Comparison of a solid oxide cell with nickel/gadolinium‐doped ceria fuel electrode during operation with hydrogen/steam and carbon monoxide/carbon dioxide

Symmetrical La3+-doped Sr2Fe1.5Ni0.1Mo0.4O6-δ Electrode Solid Oxide Fuel Cells for Pure CO2 Electrolysis

Methane Partial Oxidation-assisted H2O/CO2 Co-electrolysis for Syngas Production in Both Electrodes

High performance and stability of nanocomposite oxygen electrode for solid oxide cells

Carbon Monoxide/carbon Dioxide Electrochemical Conversion on Patterned Nickel Electrodes Operating in Fuel Cell and Electrolysis Cell Modes

Redox-Reversible Electrode Material for Direct Hydrocarbon Solid Oxide Fuel Cells

Electrochemical Performance of Symmetric Solid Oxide Cells Employing a Sc-doped SrFeO3-δ-based Electrode

In Situ Exsolved CoFe Alloy Nanoparticles for Stable Anodic Methane Reforming in Solid Oxide Electrolysis Cells

Performance and Methane Production Characteristics of H2O–CO2 Co-Electrolysis in Solid Oxide Electrolysis Cells

Performance Evaluation of Solid Oxide Fuel Cell with In-Situ Methane Reforming

Study on a Novel Double-Layer Anode for Solid Oxide Fuel Cells Based on CO2 Dry Reforming of Methane

Direct Electrolysis of CO2 in Solid Oxide Cells Supported on Ceramic Fuel Electrodes with Straight Open Pores and Coated Catalysts

Electrochemical Performance of It-Sofcs with A Double-Layer Anode

Solid Oxide Cells with Phase-Inversion Tape-Casted Hydrogen Electrode and SrSc<sub>0.175</sub>Nb<sub>0.025</sub>Co<sub>0.8</sub>O<sub>3</sub><sub> -</sub> Oxygen Electrode for High-Performance Reversible Power Generation and Hydrogen Production

Redox of Ni/YSZ Anodes and Oscillatory Behavior in Single-Chamber SOFC under Methane Oxidation Conditions

Functionally Graded Infiltration Triggering Ultrahigh Electrolytic Current in Robust Reversible Solid Oxide Cells

Enhanced electrochemical performance and durability for direct CH4–CO2 solid oxide fuel cells with an on-cell reforming layer

A Robust Flat-Chip Solid Oxide Fuel Cell Coupled with Catalytic Partial Oxidation of Methane

Solid Oxide Cells with Phase-Inversion Tape-Casted Hydrogen Electrode and SrSc0.175Nb0.025Co0.8O3-δ Oxygen Electrode for High-Performance Reversible Power Generation and Hydrogen Production