Abstract:The effect of rolling temperature on the incomplete recrystallization behavior and the relationship to mechanical properties in 0.06C–4Mn-1.2Cr (wt.%) steel was investigated. Three plates of experimental steel were produced by hot rolling at different temperatures and intercritical annealing processes in this study. The microstructure of experimental steels was examined by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The mechanical properties of test steel were examined by impact test and tensile test. Austenite reversion and cementite precipitation-dissolution was numerically simulated under the assumption of local equilibrium. With the decrease of hot rolling temperature from 1000 °C to 800 °C, the uniform equiaxed prior austenite grains microstructures changed to heterogeneous microstructures of laminated and ultrafine prior austenite grains arranged alternatively. The tensile and impact tests revealed that the medium manganese steels rolling at 800 °C had an excellent combination of mechanical properties. Elongation had a great relationship with retained austenite fraction and stability. The fractography of impact specimens was examined to explore the toughening mechanism of the micro-laminated steels. The steel with uniform equiaxed grain structure exhibited a relatively low tensile strength of 750 MPa and low elongation of ∼20% and an extremely poor low-temperature toughness of ∼40 J at −40 °C. An enhanced low-temperature toughness (∼233 J at −40 °C), as well as an improved tensile strength (823 MPa) and higher elongation of ∼40%, was obtained in the steel with heterogeneous microstructures. The content of austenite in heterogeneous microstructure is twice that in uniform equiaxed grain structure. And cementite dissolved more thoroughly in the heterogeneous microstructure. The high austenite content of heterogeneous microstructures enabled the steel to be significantly stronger and ductile, which contributed to the high tensile strength and elongation to some extent. It is concluded that the effect of interface decohesion resulted in the occurrence of delamination. And the high austenite content and delamination greatly improved the low-temperature toughness of experimental steel.

Effect of auto-tempering on the cold roll-ability of medium-Mn steel

Effect of rolling temperature on microstructure and mechanical properties of medium manganese steel

Influence of cold rolling on the stability of retained austenite and mechanical properties of a Cu bearing low carbon low manganese steel

Effect of hot/warm rolling on the microstructures and mechanical properties of medium-Mn steels

Microstructure and Mechanical Properties of Medium Mn Steel Containing 3%al Processed by Warm Rolling

Microstructure and Mechanical Properties of a Novel Cold Rolled Medium-Mn Steel with Superior Strength and Ductility

Analysis of medium manganese steel through cold-rolling and intercritical annealing or warm-rolling

Optimizing Microstructure and Mechanical Properties of Cold-Rolled Medium-Mn Steel Through Intercritical Annealing and Warm Rolling

The potential significance of tempering treatment in alleviating the hydrogen embrittlement susceptibility of a hot-rolled and intercritically annealed medium-Mn steel

Effect of precipitation-induced element partitioning during tempering on mechanical properties of hot-rolled 3Mn steel after intercritical annealing

Effect of Controlled Rolling on the Strength and Toughness of Low‐Alloy Martensitic Steel

Regulation Law of Tempering Cooling Rate on Toughness of Medium-Carbon Medium-Alloy Steel

Effect of Partition Temperature on Microstructure and Mechanical Properties of Cold‐Rolled Medium‐Manganese Steel

Effect of Cooling Practice on the Mechanical Properties of Medium‐Manganese Aluminum‐Alloyed Steels after Intercritical Annealing Quench and Partition Treatment

Effects of soaking temperature on the microstructure and mechanical properties of a medium Mn steel for hot/warm forming

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel

Ultra-Fine Heterogeneous Microstructure Enables High Strength-Ductility in a Cold-Rolled Medium Mn Steel

Effect of Cooling Process on Microstructure and Mechanical Properties of Hot Rolled 65Mn Steel

Microstructure evolution and tensile behaviour of a cold rolled 8 wt\% Mn medium manganese steel

Influence of warm rolling temperature on multi-scale lamellar structure and mechanical properties of medium carbon steel

Tailoring Strength and Ductility of a Cr-Containing High Carbon Steel by Cold-Working and Annealing