Abstract:The ConformTM process was first established in the early 1970’s for the recycling of copper and aluminium rod. Since then, the process has been developed further with the expansion into powder feedstocks and other materials such as titanium, magnesium and zinc. However, there are still significant gaps in the understanding of ConformTM – particularly for high strength feedstocks such as titanium alloys. This work sets out to develop the ConformTM process for titanium particulate feedstocks including machining swarf, in order to provide scientific insight into the challenges and process parameter requirements for the next stage of industrialisation. Through the use of discrete element modelling and experimental trials, bespoke toolsets were designed for use in the ConformTM machine and their effectiveness discussed. In this work it was shown that different powder feedstocks require different toolset geometries in order to increase the chance of extruding a consolidated product. This was further influenced by a smallscale testing rig, which assessed the densification and consolidation of powder feedstocks used in the ConformTM process and helped to determine the ‘Conform-ability’. This testing rig, known as the Arbitrary Strain Path (ASP) test machine, used bespoke tooling to replicate similar conditions to those found in the ConformTM machine, in that the feedstocks undergo both load and shear during processing. Large scale trials methods were completed using a ConformTM 350i at BWE Ltd., Ashford, UK. The trials were conducted using bespoke tooling designed for this project and resulted in, in a number of cases, the successful extrusion of a titanium rod product. The experimental data from each trial was recorded and analysed to attempt to show further insight into the ConformTM process and demonstrate how this can influence the parameters used during a trial. The results showed that the spherical particles require more pressure to consolidate, and when coupled with the results from the simulations and experimental trials, this has shown that the smaller ConformTM toolset is more appropriate. By using the ASP and DEM simulations, there is a significant reduction in the costs of experimental testing, as the large ConformTM toolsets can cost upwards of £10000, whereas the small-scale testing and computational modelling fall in the £100s. Large scale extrusion trials were conducted on Ti-6Al-4V swarf and Ti-6Al-4V GA. The microstructure of the products often demonstrated an equiaxed fine-grained structure with grain sizes < 20 µm and limited porosity. This was reflected in the mechanical properties, which, in the case of the extruded CP Ti HDH Gr 2 feedstock, were closer to CP Ti HDH Gr 4. These results would meet requirements for additive manufacturing feedstocks and therefore the wire holds the potential of being used for downstream welding and wire-based additive manufacturing processes. This in turn highlights a potential recycling stream for aerospace waste. Overall, the thesis provides a novel, small-scale testing method for determining whether a feedstock would be suitable for ConformTM and the conditions under which it should be processed, resulting in significant cost savings. The work also develops understanding of the processing occurring during ConformTM with an insight into the trial data and how this can be analysed to provide details about the optimum extrusion parameters. Finally, the project, for the first time, reports the extrusion of waste titanium feedstocks, including swarf, into a potential product for wire-based additive manufacturing.

Analysis of Densification and Consolidation during the Solid-State Recycling of High Purity Titanium Chips

Unexpected Dynamic Recrystallization Behavior of Ti-7Cu Alloy in Semi-Solid State

Relationship of microstructure and properties of high-purity titanium manufactured by unconventional method of chips recycling

A Quantified Complex Strengthening Mechanism in Solid-State Recycled Titanium

Consolidation behavior of Mg–10Gd–2Y–0.5Zr chips during solid-state recycling

Microstructure evolution of pure titanium during hydrostatic extrusion

Discontinuous dynamic recrystallization behavior and texture evolution of large-size pure titanium flat ingot via electron beam cold hearth melting during short process direct hot rolling

Recycling of titanium as reinforcement in cast aluminium alloy A356 for improving the microstructural refinement and mechanical performance towards a sustainable material development

Development of the ConformTM process for the recycling of waste titanium into wire

Achieving high ductility in a selectively laser melted commercial pure-titanium via in-situ grain refinement

Continuous Casting and Directional Solidification of Titanium Alloys with Cold Crucible

Solid-state recycling of AZ91D magnesium alloy chips

The Α Phase Recrystallization Mechanism and Mechanical Properties of a Near-Α Titanium Matrix Composite

Recovery of Pressed Titanium Alloy Machining Chip via Vacuum Induction Melting

Deformation and Fracture Behavior of Commercially Pure Titanium with Gradient Nano-to-micron-grained Surface Layer

Dynamic Recrystallization and Silicide Precipitation Behavior of Titanium Matrix Composites under Different Strains

Surface morphology and gradient microstructural evolutions in pure titanium via surface severe plastic deformation

Microstructure and Mechanical Properties of In Situ Synthesized Metastable β Titanium Alloy Composite from Low-Cost Elemental Powders

Gradient nanostructure, phase transformation, amorphization and enhanced strength-plasticity synergy of pure titanium manufactured by ultrasonic surface rolling

Development of Rapidly Solidified Titanium Aluminide Compounds

Microstructure and mechanical characterizations of additively manufactured high oxygen-doped titanium