Abstract:Here we proposed a low-cost and high-efficiency strategy for fabricating novel multi-scale gradient-structured/heterogeneous lamella structured (GS/HLS) pure titanium laminates with superior strength-ductility synergy, by temperature-controlled rolling and subsequent annealing of as-sintered multilayered pure titanium foils with preset grain size gradient. A preliminary gradient structure with the average grain size decreasing from the center layer (alternating stacking of equiaxed fine grain bands and elongated grain bands) to the surface layer (equiaxed fine grains) is formed by optimizing the rolling process. Generalized Schmidt factor analysis based on electron backscatter diffraction indicated that there were slip-dominated and twin-dominated grain refinement mechanisms during the rolling process. In addition to the prismatic slip, two kinds of contraction twinning could be activated to achieve the grain refinement in hard domains where slip systems were hard to be activated. After subsequent annealing, equiaxed fine grains in the laminates did not significantly coarsen, while the elongated grains in the center layer had partially merged and grew up into the elongated coarse grains. Thus, the microstructure of the center layer displayed a typical heterogeneous lamella structure composed of alternately stacking of elongated coarse grains and fine grain bands, together with the grain size gradient, a unique multi-scale heterostructured titanium laminate was formed. Tensile test indicated that the as-rolled Ti laminates exhibited extremely high ultimate tensile strength (UTS) of 930 MPa with an acceptable total elongation to fracture (ETF) of 12.3 %, while GS/HLS Ti laminates after annealing at 425 °C possessed a superior combination of high UTS (823 MPa) and high ETF (22.4 %). The main reason was that the annealing treatment significantly reduced the dislocation density in the elongated coarse grains of GS/HLS Ti laminates. This meant that more geometrically necessary dislocations (GNDs) could accumulate in the plastic deformation process, resulting in the hetero-deformation induced (HDI) strengthening and an extra HDI hardening caused by the unique GS/HLS structure, therefore, an excellent strength-ductility synergy of final GS/HLS Ti laminates was achieved.

Achieving high ductility in a selectively laser melted commercial pure-titanium via in-situ grain refinement

Enhancing Ductility of Titanium Matrix Composites by Multimodal Α-Grains

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Achieving Enhanced Tensile Strength-Ductility Synergy Through Phase Modulation in Additively Manufactured Titanium Alloys

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Clarifying the formation of equiaxed grains and microstructural refinement in the additive manufacturing of Ti-Cu

Achieving near equiaxed α-Ti grains and significantly improved plasticity via heat treatment of TiB reinforced titanium matrix composite manufactured by selective laser melting

Grain refinement and improved tensile properties of Ti5Al2Sn2Zr4Mo4Cr titanium alloy fabricated by laser solid forming

Achieving Equiaxed Transition and Excellent Mechanical Properties in a Novel Near-β Titanium Alloy by Regulating the Volume Energy Density of Selective Laser Melting

Towards uniform and enhanced tensile ductility of additively manufactured Ti−5Al−5Mo−5V−3Cr alloy through designing gradient interlayer deposition time

Additive manufacturing of high-strength commercially pure titanium through lanthanum oxide addition

Strengthening layer with nano-twins in titanium alloy induced by laser surface re-melting: Mechanism of high strength and ductility

Selective laser melting of CP-Ti to overcome the low cost and high performance trade-off

Achieving superior strength-ductility synergy in a unique multi-scale heterostructured titanium laminate fabricated by temperature-controlled rolling and subsequent annealing

Nanoparticle-mediated ultra grain refinement and reinforcement in additively manufactured titanium alloys

The significant impact of grain refiner on γ-TiAl intermetallic fabricated by laser-based additive manufacturing

Developing ductile and isotropic Ti alloy with tailored composition for laser powder bed fusion

Additive manufacturing of fine-grain fully lamellar titanium aluminide alloys

Achieving grain refinement and ultrahigh yield strength in laser aided additive manufacturing of Ti−6Al−4V alloy by trace Ni addition

The effect of hydrogen on the grain refinement and mechanisms for Ti6Al4V alloys during laser melting deposition

Simultaneous enhancements of strength and ductility of a selective laser melted H13 steel through inoculation treatment