Abstract:In aero-engines, the shafts are supported on bearings that carry the radial and axial loads. A ball bearing is made up of an inner race, an outer race, and a cage, which contains the balls, these together comprise the bearing elements. The bearings require oil for lubrication and cooling. The design of the bearing studied in this work is such that the oil is fed to the bearing through holes/slots in the inner race. At each axial feed location, the oil is fed through a number of equispaced feedholes/slots but there are a different number of holes at each location. Once the oil has passed through the bearing, it sheds outward from both sides into compartments known as the bearing chambers. A number of studies have been carried out on the dynamics of bearings. Most of the analyses consider the contributions of fluid forces as small relative to the interaction of the bearing elements. One of the most sophisticated models for a cage–raceway analysis is based on the work of Ashmore et al. (2003, “Hydrodynamic Support and Dynamic Response for an Inner-Piloted Bearing Cage,” Proc. Inst. Mech. Eng. Part G, 217, pp. 19–28], where the cage–raceway is considered to be a short journal bearing divided into sectors by the oil feeds. It is further assumed that the oil exits from the holes and forms a continuous block of oil that exits outward on both sides of the cage–raceway. In the model, the Reynolds equation is used to estimate the oil dynamics. Of interest in this current work is the behavior of the oil and air within the space bounded by the cage and inner race. The aim is to determine whether oil feed to the bearing can be modeled as coming from a continuous slot or if the discrete entry points must be modeled. A volume of fluid (VOF) computational fluid dynamics (CFD) approach is applied. A sector of a ball bearing is modeled with a fine mesh, and the detailed simulations show the flow behavior for different oil splits to the three feed locations of the bearing, thus providing information useful to understanding oil shedding into the bearing chambers. This work shows that different flow behaviors are predicted by models where the oil inlets through a continuous slot are compared to discrete entry holes. The form and speed of oil shedding from the bearing are found to depend strongly on shaft speed with the shedding speed being slightly higher than the cage linear speed. The break-up pattern of oil on the cage inner surface suggests that smaller droplets will be shed at higher shaft speed.

Experimental and numerical investigation on thermodynamic performance of full-floating ring bearings with circumferential oil groove

Numerical Investigation of Air–Oil–Thermal Coupling Mechanism in Floating Ring Bearings

Experimental and Numerical Analysis of a Self-Circulating Oil Bearing System for Gear Pumps

Experimental and Numerical Study of the Influence of Loading Direction on the Lubrication and Cooling of Self-Circulating Oil Bearing System Applied in Internal Gear Pumps

Analytical and Experimental Method of Thermal Load Estimation for Seals in Transmission of Vehicle

Numerical Investigation of Subsynchronous Vibration in Floating Ring Bearings

Dynamic Analysis of Turbocharger Rotor Bearing with an Integrated Three Dimensional Thermohydrodynamic Model

Numerical and Experimental Investigation on Thermohydrodynamic Performance of Turbocharger Rotor-Bearing System

Coupling analysis of tribological and dynamical behavior for a thermal turbulent fluid lubricated floating ring bearing-rotor system at ultra-high speeds

Numerical and Experimental Studies on Stability of Cryogenic Turbo-Expander with Protuberant Foil Gas Bearings

Analysis of Circulation Characteristics and Heat Balance of High-Speed Rolling Bearing under Oil-Air Lubrication

Investigation Of Air-Oil-Thermal Distribution In Floating Bush Bearings

Influence of Rotational Speed on Oil Film Temperature of Multi-Sector Recess Hydrostatic Thrust Bearing

Lubrication and stability analysis of nonlinear rotor-bearing system

Investigation on the nonlinear dynamic behaviors of water-lubricated bearings considering mixed thermoelastohydrodynamic performances

Analysis of Oil-Air Two-Phase Flow Characteristics inside a Ball Bearing with Under-Race Lubrication

Research on the Condition of Nonisothermal-based Lubrication Problem of the Externally Pressurized Gas Bearings

Numerical Investigation for Characteristics and Oil–air Distributions of Oil Film in a Tilting-Pad Journal Bearing

A Computational Fluid Dynamics Simulation of Oil–Air Flow Between the Cage and Inner Race of an Aero-engine Bearing

Vibration characteristics of turbocharger rotor system considering internal thread texture parameters of semi-floating ring bearing

A Thermohydrodynamic Analysis of the Self-Lubricating Bearings Applied in Gear Pumps Using Computational Fluid Dynamics Method