Abstract:Abstract This paper analyses the flow characteristics and oil-air distributions of oil flows in a tilting-pad journal bearing under different bearing loads. This titling-pad journal bearing is working at 3000 rpm rotation speed and its minimum film thicknesses have been measured under different loads from 180 kN to 299 kN. Based on the previous researches of this bearing under 180 kN, the gaseous cavitation and low-turbulence flow exists in this bearing flow. A suitable gaseous cavitation model and the SST model with low-Re correction are used in the film flow simulations. With the rotor and pads assumed to be rigid, the dynamic mesh and motion equations are applied to simulate the motions of the rotor and the rotations of the pads. Based on the simulation results under different bearing loads, the simulated minimum film thicknesses agrees well with the measured data. It indicates that the simulation results can catch the film geometries and flows correctly. With the load increasing, the rotor moves closer to the loaded pads and the minimum film thickness decreases. Taking the effect of boundary layers into consideration, the turbulence has a negative relationship with the film thickness and decreases in the loaded area under higher bearing load. It can be verified by the simulated lower turbulent viscosity ratio distributions in the loaded pads. In the unloaded area, both the film thickness and turbulence viscosity ratio are positively related to the bearing loads. Thus, the higher bearing load may lead the flow to be more different in the loaded and unloaded area, and the turbulence in the loaded pads may transfer to laminar in the end. As for the oil-air distributions, in the unloaded pads, with the bearing load increasing, the simulated air volume fraction increases in the unloaded pads with lower pressure. It should be caused by the higher film thickness of the unloaded pads under higher loads. In sum, the flow turbulence and cavitation process changes with the bearing load. With a higher load, the cavitation becomes more in the unloaded pads and the flow changes sharper from the high-turbulence unloaded area to the low-turbulence loaded area. As the simulation results is in good accordance with the experimental data, the SST model with low-Re correction and the gaseous cavitation model are verified to be suitable for bearing film simulations under different loads.

Experimental and Numerical Study of the Influence of Loading Direction on the Lubrication and Cooling of Self-Circulating Oil Bearing System Applied in Internal Gear Pumps

Experimental and Numerical Analysis of a Self-Circulating Oil Bearing System for Gear Pumps

Lubrication Performance Analysis of Lead-Bismuth Internal-Feedback Bearings in the Nuclear Main Pump System

Multi-objective Optimization Design of Sliding Bearing of High-speed Centrifugal Pump Based on Lubrication Characteristics Analysis

Numerical Analysis of Lubrication Property for Port Plate Pair of Axial Piston Pump

A Thermohydrodynamic Analysis of the Self-Lubricating Bearings Applied in Gear Pumps Using Computational Fluid Dynamics Method

Investigation of hydrodynamic lubricant film breakdown between the journal and bearing in a high-speed coolant pump of electric vehicles

Lubrication and stability analysis of nonlinear rotor-bearing system

Numerical analysis of the lubricating gap between the gear shaft and the journal bearing in water hydraulic internal gear pumps

Analysis of Circulation Characteristics and Heat Balance of High-Speed Rolling Bearing under Oil-Air Lubrication

Hydrostatic bearing groove multi-objective optimization of the gear ring housing interface in a straight-line conjugate internal meshing gear pump

Theoretical and Experimental Investigations on Directly Lubricated Tilting Pad Journal Bearing under Starved Lubrication

Experimental and numerical investigation on thermodynamic performance of full-floating ring bearings with circumferential oil groove

A Numerical Investigation of Mixed Thermal Elastohydrodynamic Lubrication in Tilting-Pad Journal Bearing

Analysis of lubrication performance and flow field for lead-bismuth bearings considering the temperature-viscosity effect

Influence of Rotational Speed on Oil Film Temperature of Multi-Sector Recess Hydrostatic Thrust Bearing

The Numerical Solution to Line Contact Elastohydrodynamic Problems under Heavy Load

Numerical Investigation for Characteristics and Oil-Air Distributions of a Tilting-Pad Journal Bearing Under Different Loads

Numerical simulations for the fluid-thermal-structural interaction lubrication in a tilting pad thrust bearing

Numerical Investigation for Characteristics and Oil–air Distributions of Oil Film in a Tilting-Pad Journal Bearing

Study on the influence of key design parameters on lubrication characteristics of a novel gear system applying Taguchi method