Abstract:The impact of minor Mg addition on microstructure and mechanical properties of cast Al–Li–Cu–Zr alloy with high lithium content (3 wt % Li) were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations and its effect on mechanical properties. Scanning Electron Microscope and X-ray diffraction results suggested that raising the content of Mg gradually altered the grain structure of the as-cast alloys and increased the types and volume fraction of the grain boundary intermetallic phase. Unusually, solvus temperature is higher than solidus temperature in 0.5 Mg alloy (Al–3Li–2Cu-0.5Mg-0.15Zr, wt. %), resulting in the incipient melting of the matrix before the complete dissolution of the intermetallic phases. Prominent enhancements in both age-hardening and precipitation kinetics of the base alloy with the addition of Mg were also easily identified, indicating the important role of Mg during isothermal aging. Transmission Electron Microscope and atom probe tomography results showed that minor Mg addition (0.2 wt %, denoted by 0.2 Mg alloy) could encourage the diffusion of Cu atoms by the aggregation of Mg–Cu-vacancy co-clusters, thereby promoting the nucleation of the T1-Al2CuLi and θ′-Al2Cu precipitates. In addition, S′-Al2CuMg precipitate was therefore introduced as a result of Mg addition. With further increasing the content of Mg to 0.5 wt %, the nucleation and growth of S′ precipitate would be promoted at the expense of T1 and θ′ precipitates, especially the latter. Based on the theoretical models and regression analysis, the formation mechanism of δ′-Al3Li precipitate-free-zones gradually changed from the initial vacancy-depletion mechanism to the solute-depletion mechanism, and Mg element could significantly inhibit the coarsening of δ′ precipitate-free-zones. The best balance between ductility and strength was obtained by 0.2 Mg alloy aged for 32 h, and the alloys have significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over conventional cast aluminum alloys (density: 2.7–2.8 g/cm3; elastic modulus: 72 GPa).

Quantitative Study of Microstructure-Dependent Thermal Conductivity in Mg-4Ce-xAl-0.5Mn Alloys

Effect of Ce Addition on the Microstructure, Thermal Conductivity and Mechanical Properties of Mg–0.5Mn Alloys

Thermal Characteristics of Mg–Zn–Mn Alloys with High Specific Strength and High Thermal Conductivity

Microstructure and Thermal Conductivity of As-Cast and As-Extruded Binary Mg–Mn Alloys

Effect of Extrusion Temperature on the Microstructure and Thermal Conductivity of Mg–2.0Zn–1.0Mn–0.2Ce Alloys

Microstructure and Thermal Conductivity of As-Cast and As-Solutionized Mg–Rare Earth Binary Alloys

Thermal and electrical conductivity of binary magnesium alloys

Effect of Ce Addition on Microstructure, Thermal Conductivity, and Mechanical Properties of As-Cast and As-Extruded Mg–3Sn Alloys

Microstructure Formation of Al-Based Alloys in the Presence of Rare Earth Metals (Ce, La) and Mn under High Cooling Rate

Microstructure and thermophysical properties of Mg-2Zn-xCu alloys

Numerical study of the effective thermal conductivity of 2-phase magnesium alloys containing solid solution atoms using lattice Monte-Carlo

Study on the Microstructure of Mg-4Zn-4Sn-1Mn-xAl As-Cast Alloys

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Microstructures and Mechanical Properties of As-Cast Mg–5Al–0.4Mn–xNd (x = 0, 1, 2 and 4) Alloys

Effects of La Addition on the Microstructure, Thermal Conductivity and Mechanical Properties of Mg-3Al-0.3Mn Alloys

Effects of Al Concentration on Microstructure and Mechanical Properties of Mg-xAl-1Zn-1Si Alloy

A high performance Mg-Al-Ca alloy processed by high pressure die casting: Microstructure, mechanical properties and thermal conductivity

Effect of Al on the Microstructure and Mechanical Properties of Mg–Sn–Ca–Mn Wrought Alloy

Elucidating thermal conductivity mechanism of Al-9Si based alloys with trace transition elements (Mn, Cr, V)

Significant roles of minor Mg addition in microstructural evolution and mechanical properties of cast Al–3Li–2Cu-0.15Zr alloy

Alloying effect of Mg on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy