Abstract:γ-Alumina with incorporated metal oxide species (including Fe, Cu, Zn, Bi, and Ga) was synthesized by liquid-assisted grinding-mechanochemical synthesis, applying boehmite as the alumina precursor and suitable metal salts. Various contents of metal elements (5 wt.%, 10 wt.%, and 20 wt.%) were used to tune the composition of the resulting hybrid materials. The different milling time was tested to find the most suitable procedure that allowed the preparation of porous alumina incorporated with selected metal oxide species. The block copolymer, Pluronic P123, was used as a pore-generating agent. Commercial γ-alumina (SBET = 96 m2·g-1), and the sample fabricated after two hours of initial grinding of boehmite (SBET = 266 m2·g-1), were used as references. Analysis of another sample of γ-alumina prepared within 3 h of one-pot milling revealed a higher surface area (SBET = 320 m2·g-1) that did not increase with a further increase in the milling time. So, three hours of grinding time were set as optimal for this material. The synthesized samples were characterized by low-temperature N2 sorption, TGA/DTG, XRD, TEM, EDX, elemental mapping, and XRF techniques. The higher loading of metal oxide into the alumina structure was confirmed by the higher intensity of the XRF peaks. Samples synthesized with the lowest metal oxide content (5 wt.%) were tested for selective catalytic reduction of NO with NH3 (NH3-SCR). Among all tested samples, besides pristine Al2O3 and alumina incorporated with gallium oxide, the increase in reaction temperature accelerated the NO conversion. The highest NO conversion rate was observed for Fe2O3-incorporated alumina (70%) at 450 °C and CuO-incorporated alumina (71%) at 300 °C. The CO2 capture was also studied for synthesized samples and the sample of alumina with incorporated Bi2O3 (10 wt.%) gave the best result (1.16 mmol·g-1) at 25 °C, while alumina alone could adsorb only 0.85 mmol·g-1 of CO2. Furthermore, the synthesized samples were tested for antimicrobial properties and found to be quite active against Gram-negative bacteria, P. aeruginosa (PA). The measured Minimum Inhibitory Concentration (MIC) values for the alumina samples with incorporated Fe, Cu, and Bi oxide (10 wt.%) were found to be 4 µg·mL-1, while 8 µg·mL-1 was obtained for pure alumina.

Alpha-Alumina Synthesis Using Gamma-Alumina Powders

Study of Gamma Alumina Synthesis – Analysis of the Specific Surface Area

Synthesis and sintering behavior of a nanocrystalline α-alumina powder

Microstructure and Properties of Alumina Ceramics Prepared from Submicrometer Alumina Powder with MgO–ZrO2 Coated on Alumina Grain Surface

Preparation and properties of Al2O3/Al-2(1-0.2)Mg0.2Ti(1+0.2)O5 matrix ceramic composite

Preparation and research of fine-grained alumina with high mechanical properties

Exploring the Multifunctionality of Mechanochemically Synthesized γ-Alumina with Incorporated Selected Metal Oxide Species

Production of ultrafine alpha alumina powders and fabrication of fine grained strong ceramics

A Novel Synthesis Route of Mesoporous γ-Alumina from Polyoxohydroxide Aluminum

Synthesis, Evaluation And Characterization Of Alumina Ceramics With Elongated Grains

Effect of Synthesizing Temperature of Alumina Powder with Rose-Like Structure on the Microstructure and Mechanical Property of Alumina Ceramic

Preparation of Β"-Alumina with Η Type Nanometer Alumina Powder Via Solid Phase Synthesis

Approach toward Alpha Alumina Synthesis

Microstructural Optimization of Alumina Prepared from Ultrafine Theta-Phase Powder for High Strength Applications

Effect of Alpha-Al2o3 Micro Powder on Performance of Porous Plug Well Block

Preparation of Composite Spherical Alumina Nanoparticles and Study on their CMP Performance

Microstructure and Performance of Nanometer Γ-Al2o3p/al Composite Fabricated in Al-Co3O4 Components

Influence of Alumina Grade on Sintering Properties and Possible Application in Binder Jetting Additive Technology

Preparation and Properties of Nano BaNb2O6-Al2O3 Ceramic Composites

Structural and mechanical optimization of porous alumina structures fabricated by carbon sacrificial template

Insights into Intragranular Precipitation and Strengthening Effect in Al2O3/SmAlO3 Ceramic with Eutectic Composition