Abstract:A comprehensive research project consisting of pilot-scale combustion testing and long-term laboratory corrosion study has been performed. A pilot-scale combustion facility was modified to enable burning of pulverized coals under the conditions typical for coal-fired utility boilers. Eight United States (U.S.) coals were selected for this investigation, with the test conditions for all coals set to have the same heat input to the combustor. In addition, the air/fuel ratio was controlled so that approximately 3% excess oxygen was attained in the combustion gas at the furnace outlet, a location equivalent to the furnace exit of commercial boilers. During each pilot-scale combustion test, extensive online measurements of the flue gas compositions were performed. In addition, deposit samples were collected at the same location for chemical analyses. This information characterized well the combustion environments adjacent to the superheaters and reheaters of utility boilers burning different U.S. coals. The gas and deposit compositions were then simulated in a series of 1000-hour laboratory corrosion tests in which the corrosion performances of different alloys were evaluated at 704oC (1300oF). Results of this laboratory study led to better understanding of the corrosion mechanisms operating on superheaters and reheaters in coal-fired boilers due to the mutual presence of sulfur and chlorine in coal. A new corrosion mechanism, i.e., “Active Sulfide-to-Oxide Corrosion Mechanism,” accounts for the rapid corrosion attack on low-alloy ferritic steels and lower-grade stainless steels resulting from the formation of iron chloride (FeCl2) vapor and associated cycling reactions. For higher alloys containing sufficient chromium, the attack is dominated by Hot Corrosion in the presence of a fused salt. In addition, two stages of the hot corrosion mechanism have been elucidated here in detail. The initiation of hot corrosion attack induced by molten sulfate may involve Stage 1 “acidic” fluxing and re-precipitation of the protective scale formed initially on the deposit-covered alloy surfaces, followed by Stage 2 Hot Corrosion dominated by “basic” fluxing and re-precipitation after the scale is locally penetrated by the fused salt.

Coal-Ash Corrosion of a Chromium-Molybdenum Steel Superheater Tube

High-Temperature Corrosion Properties of Boiler Steels under A Simulated High-Chlorine Coal-Firing Atmosphere

High-temperature corrosion data and mechanisms for T122, Super304H and HR3C after 15 years in 1000MW ultra-supercritical power plant

Analysis of Frequent Tube Burst of High Temperature Reheater in 600 MW Unit

A Typical Super-Heater Tube Leakage and High Temperature Corrosion Mechanism Investigation in a 260 T/h Circulated Fluidized Boiler

Failure Analysis of Stainless Steel Heat Exchanger Tubes in a Petrochemical Plant

Microstructural Evolution and Oxidation Resistance of T92 Boiler Tube Steel Upon Long-Term Supercritical Steam Test

Case Study on Fireside Erosion of Platen Superheater Boiler Tubes of a Coal-Fired Power Plant

Failure Analysis of T91 Finish Superheater Tube in 660 MW Supercritical Thermal Power Plant

Failure analysis of steam superheater boiler tube made of ASTM T22 steel

Intergranular corrosion susceptibility of a novel Super304H stainless steel

Failure analysis of reheater tubes in a 350 MW supercritical circulating fluidized bed boiler

Failure analysis of sulphidation-oxidation corrosion of Incoloy 800HT superheater tube

Corrosive damage analysis and characterization of boiler tubes in a secondary superheater

High-Temperature Degradation and Protection of Ferritic and Austenitic Steels in Steam Generators

Failure Analysis of T12 Boiler Re-Heater Tubes During Short-Term Service

High-Temperature Corrosion Mechanisms for Selected Iron and Nickel-Based Alloys Exposed to Sulfur and Chlorine-Containing Environments

Failure Analysis of Utility Boiler Superheater Tubes of A213 T12

Cause Analysis of Superheater Tube Cracking in Medium Temperature Separated Circulating Fluidized Bed Boiler