Abstract:In this study, combustion synthesis involving mechanical milling and subsequent sintering process was utilised to fabricate Cu/AlxCuy/Al2O3 in-situ composite through the aluminothermic reduction of CuO powders. First, CuO and Al powders were mixed, and ball milled for 30–150 min to facilitate self-propagating high-temperature synthesis (SHS). Then, mechanically activated Al-CuO powders were mixed with elemental Cu powders and experienced subsequent cold compaction and sintering processes. The reactions during synthesis were studied utilising differential thermal analysis (DTA), X-ray diffraction (XRD), and scanning electron microscopy (SEM). Densification and hardness of green and sintered bodies were also obtained. The results indicated that despite the negative free energy of the aluminothermic reaction, an initial activation energy supply is required, and mixed Al-CuO powders did not show significant progress in the combustion synthesis method. The aluminothermic reaction became probable whenever the activation energy was entirely provided by high-energy ball milling or by the sintering of ball-milled Al-CuO mixed powders. DTA results showed that the aluminothermic reaction temperature of Al-CuO decreased with milling times, whereas after 150 min of ball milling, the reaction was completed. XRD patterns revealed that the formation of Al2Cu and Al2O3 reinforcing phases resulted from CuO reduction with Al. Al4Cu9, Cu solid solution, and Al oxide phases were observed in sintered samples. The relative density of the samples was reduced compared to the green compacted parts due to the nature of the Cu-Al alloy and the occurrence of the swelling phenomenon. The hardness results indicated that in-situ formation of reinforcing phases in samples that experienced thermally assisted thermite reaction yielded superior hardness.

A Self-propagating high-temperature synthesis process for the fabrication of Fe(Cr)–Al2O3 nanocomposite

Full-density nanocrystalline Fe-29Al-2Cr intermetallic consolidated from mechanically milled powders

Mechanical Activation-Assisted Solid-State Aluminothermic Reduction of CuO Powders for In-Situ Copper Matrix Composite Fabrication

Structural, magnetic and electron transfer effect of Cr additive on Fe 65 Co 35 nanopowder fabricated mechanical alloying

Mechanism of synthesizing Al2O3/Fe-Al composites with nano Al2O3 fibers by in-situ process

Effect of Cr on Microstructure, Mechanical Properties, and Wear Behavior of in Situ 20 Wt.%al2o3/fe-25Al Composites

Investigation on NiAl–TiC–Al2O3 Composite Prepared by Self-Propagation High Temperature Synthesis with Hot Extrusion

Mechanical synthesized nanocrystalline Ti/Al composite powders as precursor for Ti/Al alloy via reactive sintering

Al3Ti/Al composites prepared by SHS

Fabrication and wear behavior of TiC/TiB 2 -reinforced NiAl intermetallic matrix composites

Mechanical Alloying and Spark Plasma Sintering of Ni-Al-Ti-B Powders for Fabricating Nanocrystailine (Tib+tib2)/ni-3(Al, Ti) Composite

Synthesis of Fe2O3/Al Nanocomposite and Research on Its Thermite Reaction

Preparation of a hard AlTiVCr compositionally complex alloy by self-propagating high-temperature synthesis

In Situ Synthesis of Al–TiC in Aluminum Melt

Boron Carbide Composites produced by Self-Propagating High-Temperature Synthesis

The synthesis of CoAl0.3Fe1.7O4/SmFeO3 nanocomposites with enhanced properties for technological applications

Synthesis of Al2O3-WSi2-WB2-WB composite in Al-Si-WO3-B2O3 system by self-propagating high-temperature synthesis

Structure and Phase Composition of SHS Products in Powder Mixtures of Titanium, Carbon, and Aluminum

Fabrication of Nano-MgO Reinforced Fe-Cr-Ni Composites by Reactive Hot Pressing

Effect of 4 wt.% Cr on microstructure, corrosion resistance and tribological properties of Fe3Al-20 wt.%Al2O3 composites

Porous Nano-Al2o3/fe–cr–ni Composites Fabricated by Pressureless Reactive Sintering