Abstract:A key property for high-frequency inductive applications is the magnetic softness, ideally characterized by complete reversibility of the hysteresis curve. Magnetic softness of alloys depends on the dimensional ratio of grain size to the correlation length. The random anisotropy model predicts the optimum magnetic softness if the crystallite size is well below the correlation length. Based on this theory, a common strategy in processing is to obtain extremely fine nanoscale grains via rapidly solidified alloys, followed by a controlled vacuum anneal. As is well known, this conventional approach requires two demanding experimental conditions: 1) an extremely high quench rate, & x003E;10(5) K/s, and 2) a high vacuum anneal near 600 & x00B0;C to avoid oxidation. Furthermore, the completely amorphous ribbon is extremely elastic and mechanically strong and is not easily made into the fine powder form for net-shaping and 3-D printing of the soft magnets. Therefore, annealing to induce crystallization is a necessary step before using any conventional powdering techniques, such as ball milling. In this article, we report a new processing strategy of making Fe77Ni5.5Co5.5Zr7B4Cu powders directly from the as-spun ribbons without any crystallization annealing step. This is achieved by melt spinning of the alloy at a relatively low quenching rate, resulting in partially crystallized ribbons that deform plastically, a behavior that is in sharp contrast to its amorphous counterpart. The ribbon samples are ball milled into fine powders by tungsten carbide (WC) at various time intervals. Magnetization measurements show extremely low coercive field (Hc) of 0.51 Oe for the powder that is ball milled for 60 min. However, Hc consistently increases with ball milling time, as the samples are strain-hardened, introducing more magneto anisotropy. The coercive fields of these samples are easily recovered during the high-temperature magnetization measurement at 900 K, and an Hc of 3.78 Oe is obtained upon recovery. This strategy paves a new way for straightforwardly making soft magnetic powders while avoiding high quenching rate requirement and the possibility of oxidation during annealing.

A review of processing techniques for Fe-Ni soft magnetic materials

A review of soft magnetic properties of mechanically alloyed amorphous and nanocrystalline powders

Magnetic Properties of Fe–50%Ni Alloy Fabricated by Metal Injection Molding

Functional Grading Between Soft-Magnetic Fe-Co/Fe-Ni Alloys and the Effect on Magnetic and Microstructural Properties

Recent Advances in Additive Manufacturing of Soft Magnetic Materials: A Review

Microstructure and Magnetic Properties of Fe–50%Ni Alloy Fabricated by Powder Injection Molding

Synthesis and Magnetic Properties of Nb-doped Al–Ni–Co–Ti–Cu–Fe Permanent Magnets

L10 FeNi: a promising material for next generation permanent magnets

Preparation of High Performance Sintered Soft Magnetic Alloy by Metal Injection Molding

Preparation of Fe–Si–Ni soft magnetic composites with excellent high-frequency properties

Preparation, Magnetic and Mechanical Properties of Fe/Ni-Based Amorphous Fibers

Optimization of magnetization and mechanical properties of Fe-Ni-based alloys by Response Surface Methodology

Soft Magnetic Composites Based on the Fe Elemental, Binary and Ternary Alloy Systems Fabricated by Surface Nitridation

NiFe Nanoparticles: A Soft Magnetic Material?

Research Progress of Fe-based Amorphous / Nanocrystalline Alloys

Effect of Fe-Ni Substitution in FeNiSiB Soft Magnetic Alloys Produced by Melt Spinning

Additive manufacturing of magnetic materials

Magnetic and Mechanical Properties of Fe-based Α-Fe2o3/nano-sized MgO-coated Composites

Preparation of FeNiMo/SiO<sub>2</sub> Composite Core and Regulation of Soft Magnetic Properties

New Developments in NdFeB-Based Permanent Magnets

Processing of Soft Magnetic Fine Powders Directly from As-Spun Partial Crystalline Fe 77 Ni 5.5 Co 5.5 Zr 7 B 4 Cu Ribbon Via Ball Mill Without Devitrification