Abstract:INTRODUCTION Gallium nitride (GaN) is of particular interest due to its direct wide band gap energy (3.4 eV), high breakdown field, high electron saturation velocity and outstanding physicochemical properties [1-2]. For device applications, a GaN film is generally prepared by metal organic chemical vapor deposition (MOCVD) on sapphire substrates. However, in these heteroepitaxial GaN layers, the lattice and thermal mismatch between GaN and sapphire leads to a large number of dislocations [3]. As a result, flat, clean and undamaged surface is essential to form homo-epitaxial GaN layers with a low dislocation density [4]. However, GaN is very difficult to achieve an ideal polishing efficiency because of its high hardness and stable chemical properties [5]. Mechanical polishing with hard abrasives such as diamond and alumina particles can achieve flatness rapidly, but it can introduce scratch damages [6]. Wet etching can planarize GaN surface without damage by using photo electrochemical treatment, hot phosphoric acid, and molten KOH [7], but it produces rough surface. An etching method, which termed catalyst-referred etching (CARE) has been reported to produce an atomically flat damagefree surface of GaN [8], but the removal rate was just 3.4-3.8 nm/h [5]. Chemical-mechanical polishing (CMP) is considered to be an effective method to realize atomic-level smooth and damages free surface of materials. The studies of Hayashi et al.[9] suggested the importance of the selection of abrasive particles and led to the conclusion that abrasive should be softer than GaN to suppress the introduction of sub-surface damage layers. Colloidal silica based slurry is one of the possible candidates to achieve a damage free surface with a true CMP process as colloidal silica is much softer than GaN [10]. Hideo Aida et al. [11] reported the CMP process of gallium face of GaN with colloidal silica based slurry. In their studies, there were a lot of scratches generated during polishing process, which under the condition of abrasive particle size and concentration of 40nm and 40% respectively. It took him about 150 h to obtain damage-free surface. In our previous published work, we got damage-free surface within 9 h by using Al2O3 and colloidal silica slurry respectively [12]. The purpose of this work is to make clear of the principal influence factors in scratches on the surface of GaN during CMP process, to fulfill controllable and optimization CMP process, and provide a reference basis for the material removal mechanism of GaN.

A Novel Strategy Achieving GaN Ultra-Smooth Surface via a Square, Flat Top Beam Shaped Femtosecond Laser Processing Combined with Chemical Mechanical Polishing

A synergistic polishing technology by mixed abrasives with photocatalysis and fenton reaction

Analysis of scratches generated on gan substrates during polishing

Optimization and Mechanism of SiO2-Based Slurry Components for Atomically Smooth Gallium Nitride Surface Obtained Using Chemical Mechanical Polishing Techniques

Atomically Smooth Gallium Nitride Surface Prepared by Chemical-Mechanical Polishing with Different Abrasives

Chemical Mechanical Polishing of Freestanding GaN Substrates

Atomically smooth gallium nitride surface prepared by chemical-mechanical polishing with S2O82−-Fe2+ based slurry

Towards obtaining high-quality surfaces with nanometric finish by femtosecond laser ablation: A case study on coppers

Thinning of N-face GaN (0001 ¯) Samples by Inductively Coupled Plasma Etching and Chemomechanical Polishing

Atomically smooth gallium nitride surfaces generated by chemical mechanical polishing with non-noble metal catalyst(Fe-Nx/C) in acid solution

One-step fabrication of fine surfaces via femtosecond laser on sliced SiC

Surface modulation to enhance chemical mechanical polishing performance of sliced silicon carbide Si-face

Highly efficient and atomic scale polishing of GaN via plasma-based atom-selective etching

Nanosecond laser polishing of laser nitrided Zr-based metallic glass surface

Formation Mechanism of a Smooth, Defect-Free Surface of Fused Silica Optics Using Rapid CO2 Laser Polishing

Improving Polishing Efficiency of RB-SiC through Femtosecond Laser Pretreatment

Centimeter-scale low-damage micromachining on single-crystal 4H–SiC substrates using a femtosecond laser with square-shaped Flat-Top focus spots

Effects of Catalyst Concentration and Ultraviolet Intensity on Chemical Mechanical Polishing of GaN

Molecular Dynamics Simulation of Laser Assisted Grinding of GaN Crystals

Achieve 2-inch-diameter homogeneous GaN films on sapphire substrates by pulsed laser deposition

A Study of Surface Defects of GaN During CMP Process