Abstract:Hollow fiber membranes fabricated via dry/wet phase inversion method usually have two dense skin layers,which will increase its resistance of mass transport as a support membrane. It is necessary that the dense skin layer of support membrane has been eliminated to improve separation performance of composite membrane. The excellent. chemical resistance of poly(vinylidene fluoride) (PVDF) to many acids and alkalis has made it as an attractive membrane material, and then it's often fabricated as porous hollow fiber membrane by phase inversion. In the process, the formation of the skin layer is due to the rapid exchange between solvent and coagulation, so many attempts have been made to slow it, so as to control the formation of the skin layer. In this paper, it has been found that the fabrication progress becomes unstable, and the membrane prepared has noncircular lumen, when the "weak" or "soft" coagulation is used. To increase the fabrication solution stability during membrane formation, dope viscosity was focused in this experiment. Dimethyl acetamide (DMAc) was used as solvent as well as internal coagulant, and the additives including LiCl, water and surfactant Span were chosen to investigate their effect oil the viscosity of the fabrication solution. The dope viscosity will greatly increase after adding LiCl, while the variety of dope viscosity is unconcerned in the fabrication solution concentration as adding water. The homogenization and stability of the fabrication solution are improved by adding Span,and the viscosity increases at the same time. Without increasing PVDF concentration, the stability of the nascent membrane was improved by increasing the fabrication viscosity. The PVDF hollow fiber membrane with the structure of single outer skin layer and finger-like pore through the cross-section, has been successfully fabricated. The mean pore radius and water flux of the single skin hollow fiber membrane were greatly improved.

Effect of the Post-Spinning Solvent Exchange on the Performance of Asymmetric, Polyimide Hollow Fibers Prepared by Using a Triple-Orifice Spinneret

Hollow Fiber Polyimide Membranes Prepared in a Triple Orifice Spinneret: Effect of a Reduced Water Activity in the Bore Fluid on the Gas Separation Performance

Structure formation and characterization of PVDF hollow fiber membranes by melt-spinning and stretching method

Effect of Preparation Parameters on the Structure of PVDF Hollow Fiber Membranes

Effect of Physical Aging on Gas Transport in Asymmetric Polyimide Hollow Fibers Prepared by Triple-Orifice Spinneret

Experimental And Numerical Analyses On The Poly(Lactide-Co-Glycolide) Hollow Fiber Membranes

Physicochemical Characteristics of Hollow Fiber Structured Packings in Isopropanol/Water Distillation

Effect of Spinning Conditions on the Structure and Performance of Hydrophobic PVDF Hollow Fiber Membranes for Membrane Distillation

Tailoring Nonsolvent-Thermally Induced Phase Separation (N-TIPS) Effect Using Triple Spinneret to Fabricate High Performance PVDF Hollow Fiber Membranes

Effect of Viscosity and Air Gap within the Spinneret on the Morphology and Mechanical Properties of Hollow-Fiber Polymer Membranes for Separation Performance

Influence of Dope Viscosity on the Fabrication of Pvdf Hollow Fiber Membranes with Single Skin Layer

Dry–wet spinning of temperature-sensitive PVDF hollow-fiber membranes at different bore fluid flow rates

Influence of non-solvent chemistry on polybenzimidazole hollow fiber membrane preparation

Separation of Alcohol−Water Solutions by Distillation Through Hollow Fibers

Ethanol-water Separation in Hollow Fiber Membrane Contactor

The Effects of Spinning Temperature on Morphologies and Properties of Polyethersulfone Hollow Fiber Membranes

Use ionic liquids for hollow fiber spinning

Enhancing thin-film composite polyethersulfone hollow fiber membranes through alkali-induced interfacial polymerization modification for effective separation of monovalent/divalent salts

Polypropylene hollow fiber membrane prepared with green binary diluents via TIPS: Effects of spinning process parameters and VMD desalination performance

Controlling the inner surface pore and spherulite structures of PVDF hollow fiber membranes in thermally induced phase separation using triple-orifice spinneret for membrane distillation

Electric Field Simulation and Effect of Different Solvent Ratios on the Performance of Single Electrospun PVDF/PEI Composite Film